How to replace the endgate emblem and nameplate on Chevrolet Silverado 1500 Classic?

One needs a combination of tools to replace the endgate emblem and nameplate starting with these essential components: The technical tools required include a Heat Gun (J 25070) as well as a 3M TM Scotch Brite Molding Adhesive Remover Disk with part number 07501. First tape should be placed around the endgate emblem area for protection and alignment. Heat the emblem/nameplate using the heat gun (J 25070) with its nozzle 152 mm (6 in) from the surface for 30 seconds while moving in circular motions. To detach the endgate emblem/remove nameplate professionals should use a plastic flat-bladed tool then erase residual adhesive from both endgate surfaces and emblem/back using adhesive remover disks (3M(TM) P/N 07501). Wash the endgate surface using varnish makers and painters (VMP) naptha chemicals. Apply tape for guidance in unmarked areas. Use the heat gun (J 25070) to heat the endgate panel surface up to at least 21°C (70°F) without touching the emblem/nameplate adhesive layer. Press the front section of the emblem/nameplate onto the endgate panel as you proceed with removing its backing. Begin hand rolling the emblem/nameplate for adequate adhesion while checking for bonding until all tape enclosing the endgate emblem can be fully removed.

OEM Chevrolet Silverado 1500 Classic Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Emblems found

View related parts
Chevrolet Silverado 1500 Classic Nameplate, Rear Part Number: 15126056
$60.07 MSRP: $89.40
You Save: $29.33 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration; Emblem, Radiator Grille And Front End Ornamentation
- Position: Rear
- Replaces: 15034749, 15053248, 15675118, 15982992, 15998983
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Nameplate, Outer Part Number: 15036132
$48.74 MSRP: $69.75
You Save: $21.01 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Cab And Load Carrier Outer Side Decoration; Plate, Side Panel Wheel Opening; Body Side Lower Front; Fuel Door & Body Side; Pickup Box Side Lower
- Position: Outer
- Replaces: 15646974, 15705586
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Nameplate Part Number: 84674406
$42.15 MSRP: $60.31
You Save: $18.16 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate Assembly-End Gate Divider Name *Chrome; Emblem, End Gate And Rear Door Decoration; Plate, End Gate And Rear Door Decoration
- Replaces: 22884137, 15195869, 15029627
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Nameplate, Front Part Number: 15268796
$47.16 MSRP: $70.20
You Save: $23.04 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Side Door; Plate Assembly, Cab And Load Carrier Outer Side Decoration
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Emblem, Front Part Number: 12335700
$80.11 MSRP: $119.24
You Save: $39.13 (33%)
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Nameplate, Front Part Number: 15825321
Product Specifications
- Other Name: Emblem, Front Side Door; Emblem, Cab And Load Carrier Outer Side Decoration
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid | 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV)

Chevrolet Silverado 1500 Classic Emblem

Want to cut long-term maintenance and repair costs? Choose OEM Emblem. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Silverado 1500 Classic parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Silverado 1500 Classic Emblem includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Silverado 1500 Classic Emblem Parts and Q&A

Emblem, Front
12335700
Q: How to replace the endgate emblem and nameplate on Chevrolet Silverado 1500 Classic?
A:
One needs a combination of tools to replace the endgate emblem and nameplate starting with these essential components: The technical tools required include a Heat Gun (J 25070) as well as a 3M TM Scotch Brite Molding Adhesive Remover Disk with part number 07501. First tape should be placed around the endgate emblem area for protection and alignment. Heat the emblem/nameplate using the heat gun (J 25070) with its nozzle 152 mm (6 in) from the surface for 30 seconds while moving in circular motions. To detach the endgate emblem/remove nameplate professionals should use a plastic flat-bladed tool then erase residual adhesive from both endgate surfaces and emblem/back using adhesive remover disks (3M(TM) P/N 07501). Wash the endgate surface using varnish makers and painters (VMP) naptha chemicals. Apply tape for guidance in unmarked areas. Use the heat gun (J 25070) to heat the endgate panel surface up to at least 21°C (70°F) without touching the emblem/nameplate adhesive layer. Press the front section of the emblem/nameplate onto the endgate panel as you proceed with removing its backing. Begin hand rolling the emblem/nameplate for adequate adhesion while checking for bonding until all tape enclosing the endgate emblem can be fully removed.