How to clean the throttle body properly on Chevrolet Monte Carlo?

Inspection of the Throttle Body bore and throttle valve plate should begin after removing the air cleaner intake duct. Check all surfaces within the throttle valve while it remains open. Throttle position (TP) sensor, idle air control (IAC) valve and sealed throttle shaft bearing assemblies should not be cleaned with immersion cleaners or strong solvents because this cleaning method damages components with o-rings or seals while potentially clearing lubricants from non-repairable throttle shaft bearings. Avoid using wire brushes or scrapers since these tools damage Throttle Body components and exclude cleaners with methyl ethyl ketone from use because they cause unnecessary part destruction. Use gm top engine cleaner p/n 1052626 (Canadian P/N 993026) or its equivalent product to clean the Throttle Body bore while using a clean shop towel. Thorough cleaning of the Throttle Body requires disassembly followed by cleaning before reassembling and installing which must precede air cleaner intake duct reinstallation.

How to replace the throttle body assembly on Chevrolet Monte Carlo?

To remove the Throttle Body assembly, drain the cooling system. Remove the air cleaner intake duct. Thereafter the idle air control (IAC) valve connector and throttle position sensor (TP) sensor connector. Then unscrew the accelerator controls cable bracket, the Throttle Body inlet and outlet hoses. The heater pipe nut will be removed at the Throttle Body, and then the nuts and bolts which are seen to be holding the Throttle Body assembly in place taken out, and the assembly together with the Throttle Body Gasket will be removed. When cleaning the gasket surfaces on the Intake Manifold, and Throttle Body assembly, do not use any solvent since cleaning it with solvents can harm the parts; instead, clean carefully with un-sharp tools. Check on Throttle Body Gasket surfaces around mating and install new Throttle Body Gasket if necessary before reassembling Throttle Body assembly back to position. Mount the Throttle Body nuts and bolts that should be tightened to 28 n.m (21 lb ft) before reattaching the inlet and outlet hoses, and heater pipe nut that must be tightened to 25 n.m (18 lb ft). Reconnect tp sensor and iac valve electrical connectors, install accelerator controls cable bracket lastly reinstall the air cleaner intake duct. Finish the process and fill the cooling system.

OEM Chevrolet Monte Carlo Throttle Body

Fuel Injection Throttle Body

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Throttle Bodies found

View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 12568580
$332.47 MSRP: $675.28
You Save: $342.81 (51%)
ADD TO CART
Product Specifications
- Other Name: Body, Fuel Injection Air Meter; Electronic Throttle Body Assembly; Fuel Injection Throttle Body
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 12609500
$157.51 MSRP: $491.44
You Save: $333.93 (68%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body, Fuel Injection Air Meter; Electronic Throttle Body Assembly; Fuel Injection Throttle Body.
- Replaces: 12577029
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 24507235
$434.28 MSRP: $786.02
You Save: $351.74 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Kit; Body, Fuel Injection Air Meter
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Chevrolet Monte Carlo | Indianapolis 500 Pace Car, LS, Z34 | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 12595271
Product Specifications
- Other Name: Body, Fuel Injection Air Meter
- Replaces: 17113630
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 17111758
Product Specifications
- Other Name: TBI
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1988 Chevrolet Monte Carlo | Base, LS | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Monte Carlo Fuel Pressure Regulator Part Number: 17078262
Product Specifications
- Other Name: Body, Throttle Body/Carburetor; Fuel Meter; Body Kit; Metering Assembly; Throttle Body/Carburetor.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1988 Chevrolet Monte Carlo | Base, LS | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 24507241
Product Specifications
- Other Name: Body, Fuel Injection Air Meter
- Replaces: 24503396
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Monte Carlo | LT, SS | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 24507230
Product Specifications
- Other Name: Throttle Body Kit; Body, Fuel Injection Air Meter
- Replaces: 24502190, 24503390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 24507227
Product Specifications
- Other Name: Body, Fuel Injection Air Meter
- Replaces: 24507237
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 17113576
Product Specifications
- Other Name: Body, Fuel Injection Air Meter; Throttle Body Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Chevrolet Monte Carlo | LS | 6 Cyl 3.1 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 17096152
Product Specifications
- Other Name: Body, Fuel Injection Air Meter; Throttle Body Kit; Body Kit, Throttle Body/Carburetor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1998 Chevrolet Monte Carlo | LS | 6 Cyl 3.1 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Kit Part Number: 17096139
Product Specifications
- Other Name: Body-Trot; Body, Fuel Injection Air Meter
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Throttle Body Part Number: 17094010
Product Specifications
- Other Name: Throttle Body Kit; Body Kit, Throttle Body/Carburetor
- Replaces: 17113118
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Monte Carlo | LS | 6 Cyl 3.1 L GAS

Chevrolet Monte Carlo Throttle Body

Want to cut long-term maintenance and repair costs? Choose OEM Throttle Body. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Monte Carlo parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Monte Carlo Throttle Body includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

This component found in Chevrolet Monte Carlo automobiles, known as Throttle Body operates by controlling the amount of air to be let into the engine in accordance with the accelerator pedal. Located between the air cleaner and the intake manifold, it has a butterfly valve, which fluctuates to control the amount of air to be taken into the engine heads. In older models, the car used Throttle Body Injection or TBI and in the contemporary cars, multi-port fuel injection is used. ETC has become the de facto standard as for the most part, it eliminated mechanical linkage and provided better interaction with safety systems. Cleaning and replacement of different components are also required often for proper working and to increase the appliance's life span.

Chevrolet Monte Carlo Throttle Body Parts and Q&A

Throttle Body
24507227
Q: How to clean the throttle body properly on Chevrolet Monte Carlo?
A:
Inspection of the Throttle Body bore and throttle valve plate should begin after removing the air cleaner intake duct. Check all surfaces within the throttle valve while it remains open. Throttle position (TP) sensor, idle air control (IAC) valve and sealed throttle shaft bearing assemblies should not be cleaned with immersion cleaners or strong solvents because this cleaning method damages components with o-rings or seals while potentially clearing lubricants from non-repairable throttle shaft bearings. Avoid using wire brushes or scrapers since these tools damage Throttle Body components and exclude cleaners with methyl ethyl ketone from use because they cause unnecessary part destruction. Use gm top engine cleaner p/n 1052626 (Canadian P/N 993026) or its equivalent product to clean the Throttle Body bore while using a clean shop towel. Thorough cleaning of the Throttle Body requires disassembly followed by cleaning before reassembling and installing which must precede air cleaner intake duct reinstallation.
Throttle Body
12595271
Q: How to replace the throttle body assembly on Chevrolet Monte Carlo?
A:
To remove the Throttle Body assembly, drain the cooling system. Remove the air cleaner intake duct. Thereafter the idle air control (IAC) valve connector and throttle position sensor (TP) sensor connector. Then unscrew the accelerator controls cable bracket, the Throttle Body inlet and outlet hoses. The heater pipe nut will be removed at the Throttle Body, and then the nuts and bolts which are seen to be holding the Throttle Body assembly in place taken out, and the assembly together with the Throttle Body Gasket will be removed. When cleaning the gasket surfaces on the Intake Manifold, and Throttle Body assembly, do not use any solvent since cleaning it with solvents can harm the parts; instead, clean carefully with un-sharp tools. Check on Throttle Body Gasket surfaces around mating and install new Throttle Body Gasket if necessary before reassembling Throttle Body assembly back to position. Mount the Throttle Body nuts and bolts that should be tightened to 28 n.m (21 lb ft) before reattaching the inlet and outlet hoses, and heater pipe nut that must be tightened to 25 n.m (18 lb ft). Reconnect tp sensor and iac valve electrical connectors, install accelerator controls cable bracket lastly reinstall the air cleaner intake duct. Finish the process and fill the cooling system.