How to Service and Repair Brake Calipers on Front on Chevrolet K3500?

The first step for servicing or repairing the brake caliper of the c3500hd front consists of engaging the parking brake along with wheel blocking. Disassemble the brake caliper before you uninstall the hub along with its brake rotor assembly. The next step is to conduct Wheel Hub, bearing, and seal replacement (RWD-C3500HD). Unbolt the brake caliper mounting plate after removing its washers and bolts. Support rails must be checked for rust and corrosion then cleaned through wire brushing. The mounting plate should be inspected for cracks and bolt holes should be inspected for elongation and any problematic parts need replacement. Install the brake caliper mounting plate to the Steering Knuckle maintaining thread cleanliness before applying 272 threadlocker to all brake caliper mounting plate bolts. Tighten the brake shield bolts to 26 nm while using 19 ft. Lbs torque setting. Attach all bolts together with washers. Tighten the brake caliper mounting plate bolts to 105 nm (78 ft. Lbs.). After installation of the hub and brake rotor unit proceed with brake caliper installation. Finally, remove the blocks.

How to replace the rear brake calipers on Chevrolet K3500?

Tilt the vehicle to the rear, remove two-thirds of the brake fluid from the master cylinder and lift it with suitable stands before you begin. Note the connection between the wheel and the hub and come apart the wheel and the tire together. Set a C-clamp on the piston, tighten it so that the piston touches the bottom of the bore and then take the C-clamp off. Now, you should remove the brake hose and then the support key (3), the bolt (2) and the spring (4). Press out the support key with a brass punch and a hammer and after that, remove the caliper assembly (1). Inside of the caliper assembly, see if any fluid is leaking; if you notice any leakage, follow the instructions in brake caliper overhaul. A wire brush should be used to get rid of corrosion on the machined surfaces of both the anchor plate and caliper. While putting on the caliper, apply a layer of shell aeroshell grade 5 lubricant or its equal to the moving surfaces and not never seize products. Following that, install the caliper assembly (1), the spring (4) and finish by driving the support key (3) in place using a brass punch and hammer. Set the bolt (2) into the key, make sure it fits into the immediate boss in the key and tighten it to 20 Nm (15 ft. lbs.). Place the brake hose neatly and tighten it with 45 Nm (33 ft. lbs.) of torque, being sure it isn't twisted. Drain your tires, gap the rims and then fit the assembly into place. Make sure the brake pedal is firm before moving the car and after pumping the brakes, check if the brake fluid level is adequate in the master cylinder. You should lower the vehicle at the end of the process.

OEM Chevrolet K3500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Brake Calipers found

View related parts
Chevrolet K3500 Overhaul Kit, Front Part Number: 18031633
$8.47 MSRP: $15.12
You Save: $6.65 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Cylinder Piston
- Position: Front
- Replaces: 18014743
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 Chevrolet K3500 | Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Driver Side Part Number: 19140995
$45.85 MSRP: $83.62
You Save: $37.77 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18014741, 18036603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Chevrolet K3500 | Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Passenger Side Part Number: 19140994
$58.54 MSRP: $106.85
You Save: $48.31 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18014742, 18036602
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Chevrolet K3500 | Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Passenger Side Part Number: 19242899
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 14002544, 15665668
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Driver Side Part Number: 19242898
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 14002543, 15665667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Passenger Side Part Number: 18017228
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Driver Side Part Number: 18017227
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Passenger Side Part Number: 18014748
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Driver Side Part Number: 18014747
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Part Number: 18014745
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Chevrolet K3500 | Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Caliper, Front Part Number: 18014744
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Chevrolet K3500 | Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS

Chevrolet K3500 Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet K3500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet K3500 Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet K3500 Brake Calipers are part and parcel of the braking system and are well acclaimed for their mechanical efficiency that define the K3500 series trucks and vans manufactured from model year 1988 to 2002. These Brake Calipers translate hydraulic pressure from the master cylinder to mechanical force to thereby come in contact with the brake pads to the rotors for adequate stopping power. Chevrolet K3500 vehicles repairs also make use of the fixed as well as the floating calipers to enhance the stopping power of the car. Fixed adjusters can give constant pressure with dual or more working piston and floating adjusters are fit with sliders that can boost sensitivity. Chevrolet K3500 Brake Calipers are designed to be long-lasting with materials that are quite unyielding to the wear and tear which are paramount for safety. It very critical to inspect and later service these Brake Calipers to avoid situations like leakage or uneven wearing which might affect performance. The more rigid the construction of a vehicle is, the more efficiently the Brake Calipers will be effective, especially if the car is a Vortec engine equipped K3500 with powerful constructions for vigorous tasks. The unusual characteristics of high-performance materials applied in the construction of Chevrolet K3500 Brake Calipers enhance its characteristics within the automotive market, guaranteeing that both civil and application requirements are met. In conclusion, the Chevrolet K3500 Brake Calipers are solidified of the strength, functionality, and innovation that Chevrolet K3500 is characterized by, thus maintaining the vehicle's status as a reliable and high-performance car.

Chevrolet K3500 Brake Calipers Parts and Q&A

Caliper, Front Driver Side
18014747
Q: How to Service and Repair Brake Calipers on Front on Chevrolet K3500?
A:
The first step for servicing or repairing the brake caliper of the c3500hd front consists of engaging the parking brake along with wheel blocking. Disassemble the brake caliper before you uninstall the hub along with its brake rotor assembly. The next step is to conduct Wheel Hub, bearing, and seal replacement (RWD-C3500HD). Unbolt the brake caliper mounting plate after removing its washers and bolts. Support rails must be checked for rust and corrosion then cleaned through wire brushing. The mounting plate should be inspected for cracks and bolt holes should be inspected for elongation and any problematic parts need replacement. Install the brake caliper mounting plate to the Steering Knuckle maintaining thread cleanliness before applying 272 threadlocker to all brake caliper mounting plate bolts. Tighten the brake shield bolts to 26 nm while using 19 ft. Lbs torque setting. Attach all bolts together with washers. Tighten the brake caliper mounting plate bolts to 105 nm (78 ft. Lbs.). After installation of the hub and brake rotor unit proceed with brake caliper installation. Finally, remove the blocks.
Caliper, Passenger Side
19242899
Q: How to replace the rear brake calipers on Chevrolet K3500?
A:
Tilt the vehicle to the rear, remove two-thirds of the brake fluid from the master cylinder and lift it with suitable stands before you begin. Note the connection between the wheel and the hub and come apart the wheel and the tire together. Set a C-clamp on the piston, tighten it so that the piston touches the bottom of the bore and then take the C-clamp off. Now, you should remove the brake hose and then the support key (3), the bolt (2) and the spring (4). Press out the support key with a brass punch and a hammer and after that, remove the caliper assembly (1). Inside of the caliper assembly, see if any fluid is leaking; if you notice any leakage, follow the instructions in brake caliper overhaul. A wire brush should be used to get rid of corrosion on the machined surfaces of both the anchor plate and caliper. While putting on the caliper, apply a layer of shell aeroshell grade 5 lubricant or its equal to the moving surfaces and not never seize products. Following that, install the caliper assembly (1), the spring (4) and finish by driving the support key (3) in place using a brass punch and hammer. Set the bolt (2) into the key, make sure it fits into the immediate boss in the key and tighten it to 20 Nm (15 ft. lbs.). Place the brake hose neatly and tighten it with 45 Nm (33 ft. lbs.) of torque, being sure it isn't twisted. Drain your tires, gap the rims and then fit the assembly into place. Make sure the brake pedal is firm before moving the car and after pumping the brakes, check if the brake fluid level is adequate in the master cylinder. You should lower the vehicle at the end of the process.