How to Service and Repair the Turn Signal Switch on Chevrolet Impala?

You need to take off the steering column trim covers to change the Turn Signal Switch. Replace the abrasion sleeve to the steering column wire harness assembly while keeping track of its connector for reinstall later. Move the wire harness assembly free from its strap and remove the Turn Signal Switch connection with the inflatable restraint steering wheel module coil. Gently push both cables of the Turn Signal Switch from its bulkhead connector housing. Take bolts from their base in the Turn Signal Switch unit then remove this switch from the steering column. Fit the Turn Signal Switch onto the steering column tilt head device with its electrical contact surface touching the turn signal cancel cam element. Insert the bolts a and b through the Turn Signal Switch and fasten them by turning 1 nm (11 lb in). Insert the two connectors of the Turn Signal Switch into the bulkhead and connect it to the module coil connector of the inflatable restraint steering wheel column assembly. Reinsert the abrasion sleeve onto the steering column wire harness assembly but keep all wires of the ignition lock cylinder outside through its middle area. After connecting both sides of the turn signal assembly to the bulkhead connector place the wire harness assembly into the strap then put back both trim panels.

How to replace the multifunction turn signal switch on Chevrolet Impala?

Begin switching the turn signal switch by disabling the SIR system then taking off the top and bottom trim panels. Do not forget to return the abrasion sleeve to its correct position on the steering column wire harness assembly and keep track of the connector placement for later installation. Then unplug the wire harness strap from its mount and free the turn signal switch connector from the SIR system coil socket. Take the two turn signal connectors apart from the bulkhead connector then remove the two pan head tapping screws that attach the assembly to the steering column tilt head. Put the turn signal switch assembly in place on the steering column tilt head assembly so that electrical contact touches the cancel cam turn signal assembly. Insert the two screws at points and to fix the assembly. Tighten top screw to 3 Nm (27 in. lbs.) while side screw reaches 7 Nm (62 in. lbs.). Slide the two connectors into the bulkhead connector and join the turn signal switch connector to the SIR coil connector while positioning the abrasion sleeve correctly with ignition lock cylinder case wires. And complete the job by easing the wire harness back into its holder at the wire strap. Secure the trim panels then enable SIR system operation.

OEM Chevrolet Impala Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Turn Signal Switches found

View related parts
Chevrolet Impala Turn Signal Switch Part Number: 22894392
$39.65 MSRP: $71.74
You Save: $32.09 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assembly-Turn Signal; Multi Purpose Switch; Signal Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Impala | Eco, LS, LT, LTZ | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 23259228
$92.40 MSRP: $137.53
You Save: $45.13 (33%)
ADD TO CART
Product Specifications
- Other Name: Switch, Turn Signal; Multi Purpose Switch; Signal Switch; Switch, Turn Signal Lamp
- Replaces: 22894393, 23423705
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Impala | LS, LT, LTZ, Premier | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 15289426
$67.44 MSRP: $100.37
You Save: $32.93 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Headlamp/Fog Lamp/Turn Signal; Multi Purpose Switch; Combination Switch; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 23264891
$68.06 MSRP: $98.24
You Save: $30.18 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assembly-Turn Signal; Multi Purpose Switch; Signal Switch; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Impala | LS, LT, LTZ, Premier | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 88964580
Product Specifications
- Other Name: Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Combination Switch; Turn/Wiper Lever; Switch, Windshield Wiper Control; Switch, Turn Signal Lamp; Switch, Headlamp Dimmer
- Replaces: 26093873, 26073612, 26085930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 1997988
Product Specifications
- Other Name: Switch, Turn Signal; Hazard Flasher Switch; Multi Purpose Switch; Hazard Switch; Signal Switch; Turn Signal & Hazard Switch; Switch; Lever; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Chevrolet Impala | Base | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 1997984
Product Specifications
- Other Name: Switch Assembly, Turn Signal; Hazard Flasher Switch; Multi Purpose Switch; Hazard Switch; Signal Switch; Turn Signal & Hazard Switch; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Combination Switch Part Number: 19353955
Product Specifications
- Other Name: Lever, Turn Signal Control; Signal Lever; Turn/Wiper Lever; Lever
- Replaces: 25140743
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Multifunction Switch Part Number: 25111261
Product Specifications
- Other Name: Lever, Transmission Control Lever; Multi Purpose Switch; Engagement Switch; Lever
- Replaced by: 19353956
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Turn Signal Part Number: 22510733
Product Specifications
- Other Name: Lever, Turn Signal & Headlamp Dimmer Switch & Windshield Wiper & Windshield Washer; Combination Switch; Signal Lever; Turn/Wiper Switch; Turn/Wiper Lever; Lever; Lever, Turn Signal Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 88964581
Product Specifications
- Other Name: Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Combination Switch; Turn/Wiper Lever; Switch, Windshield Wiper Control; Switch, Turn Signal Lamp; Switch, Headlamp Dimmer
- Replaces: 26073613, 26093874, 26085931
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Turn Signal Switch Part Number: 1995974
Product Specifications
- Other Name: Switch Assembly, Turn Signal; Multi Purpose Switch; Signal Switch; Switch, Turn Signal Lamp; Switch, Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS

Chevrolet Impala Turn Signal Switch

Want to cut long-term maintenance and repair costs? Choose OEM Turn Signal Switch. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Turn Signal Switch includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Impala Turn Signal Switch Parts and Q&A

Turn Signal Switch
15289426
Q: How to Service and Repair the Turn Signal Switch on Chevrolet Impala?
A:
You need to take off the steering column trim covers to change the Turn Signal Switch. Replace the abrasion sleeve to the steering column wire harness assembly while keeping track of its connector for reinstall later. Move the wire harness assembly free from its strap and remove the Turn Signal Switch connection with the inflatable restraint steering wheel module coil. Gently push both cables of the Turn Signal Switch from its bulkhead connector housing. Take bolts from their base in the Turn Signal Switch unit then remove this switch from the steering column. Fit the Turn Signal Switch onto the steering column tilt head device with its electrical contact surface touching the turn signal cancel cam element. Insert the bolts a and b through the Turn Signal Switch and fasten them by turning 1 nm (11 lb in). Insert the two connectors of the Turn Signal Switch into the bulkhead and connect it to the module coil connector of the inflatable restraint steering wheel column assembly. Reinsert the abrasion sleeve onto the steering column wire harness assembly but keep all wires of the ignition lock cylinder outside through its middle area. After connecting both sides of the turn signal assembly to the bulkhead connector place the wire harness assembly into the strap then put back both trim panels.
Turn Signal Switch
88964580
Q: How to replace the multifunction turn signal switch on Chevrolet Impala?
A:
Begin switching the turn signal switch by disabling the SIR system then taking off the top and bottom trim panels. Do not forget to return the abrasion sleeve to its correct position on the steering column wire harness assembly and keep track of the connector placement for later installation. Then unplug the wire harness strap from its mount and free the turn signal switch connector from the SIR system coil socket. Take the two turn signal connectors apart from the bulkhead connector then remove the two pan head tapping screws that attach the assembly to the steering column tilt head. Put the turn signal switch assembly in place on the steering column tilt head assembly so that electrical contact touches the cancel cam turn signal assembly. Insert the two screws at points and to fix the assembly. Tighten top screw to 3 Nm (27 in. lbs.) while side screw reaches 7 Nm (62 in. lbs.). Slide the two connectors into the bulkhead connector and join the turn signal switch connector to the SIR coil connector while positioning the abrasion sleeve correctly with ignition lock cylinder case wires. And complete the job by easing the wire harness back into its holder at the wire strap. Secure the trim panels then enable SIR system operation.