How to replace the ABS Control Module on Chevrolet Colorado?

Install clean paper or shop towels on the ABS Control Module assembly before disconnecting its electrical connector. Move the connector to the Brake Booster position. Denatured alcohol enables cleaning of the master cylinder after which brake pipes must be extracted from the master cylinder to the ABS Control Module assembly while the rear brake pipe needs removing from its retainers at the cowl. Keep contaminants away from brake systems by installing rubber plugs into the brake pipes at the ABS Control Module assembly and master cylinder and brake pressure modulator valve (BPMV). Take out the ABS Control Module from your vehicle by removing its mounting nuts first then position the ABS Control Module in a dry and glove- and shop-towel-free area. The ABS Control Module needs to be positioned on its side while replacing the abs module assembly due to mounting screws which cannot be removed or break during repair. Uninstall the four mounting screws coupled with collars from the ABS Control Module and bpmv connection points while throwing away the previous pieces for new equipment. When positioning the abs module for rotation ensure that the bpmv remains facing upward and avoid misalignment of electrical connectors. The separation of ABS Control Module from bpmv should be done without any pry bar usage before discarding the solenoid plate and o-rings followed by a bpmv assembly cleaning process with dot-3 brake fluid and paper towels. Check for contamination and corrosion on solenoids and the bpmv assembly because you should replace it if necessary. The ABS Control Module assembly requires new solenoid plate and o-rings before connecting its bpmv attachment with new collars. Place mounting screws of the ABS Control Module under initial finger tightening then apply torque to 5 n.m (44 lb in). After that, attach the abs module to the vehicle and fasten the mounting nuts with a torque of 9 n.m (80 lb in). Put away rubber plugs at the brake pipe and ABS Control Module assembly site before you attach the brake pipes to the ABS Control Module assembly while tightening the fittings to 19 n.m (14 lb ft). Apply this procedure to the ABS Control Module assembly to master cylinder brake pipe installation. Attach the electrical connector while securing the rear brake pipe to its cowl retainer then pull out paper materials from within the ABS Control Module assembly interface and inner fender. The abs brake system needs bleeding before proceeding to control module reference materials which contain information about setup and replacement procedures.

OEM Chevrolet Colorado ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 ABS Control Modules found

View related parts
Chevrolet Colorado Control Module Part Number: 84330122
$254.38 MSRP: $498.06
You Save: $243.68 (49%)
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 84214765, 84004231
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 Chevrolet Colorado | Base, LT, WT, Z71, ZR2 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Modulator Valve Part Number: 84644579
$392.68 MSRP: $762.13
You Save: $369.45 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Replaces: 84004228, 84330123, 84214766, 84338036
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 Chevrolet Colorado | Base, LT, WT, Z71, ZR2 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19207520
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2012 Chevrolet Colorado | LT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121732
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967058, 19149182, 89040345
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121730
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149180, 89040343, 88967056
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121728
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967054, 19149184, 88964186
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 85620555
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Colorado | LT, Trail Boss, WT, Z71, ZR2 | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121731
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967057, 89040344
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121729
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149185, 88964188, 88967055, 89040661
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121727
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 89040659, 19149183, 88967053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 23414480
$248.88 MSRP: $446.45
You Save: $197.57 (45%)
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Modulator Valve; Module Kit, Electronic Brake Control
- Replaces: 23200278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 23414478
$490.36 MSRP: $883.54
You Save: $393.18 (45%)
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; Module, Electronic Brake Control
- Replaces: 23284603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Modulator Valve Part Number: 23354053
$609.11 MSRP: $1097.49
You Save: $488.38 (45%)
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 23200277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS

Chevrolet Colorado ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Colorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Colorado ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Colorado ABS Control Module invented for Anti-lock Braking System is a widely acclaimed model for reliability and performance on Chevrolet Colorado different models. This module is very essential for improving on the safety of the vehicles because it prevents locking of the wheels especially during vigorous braking thus improving on the handling of the vehicles. The ABS Control Module controls a complex structure of wheel speed sensors, valves, a pump, and the ECU, in that they constantly regulate the wheel speed as well as the brake pressure. This enhanced sort of braking system not only enhances the braking capacity but includes other genres like electronic stability control and traction control which increases the Authorization level of Chevrolet Colorado. The ABS Control Module is compatible with several generations of the Colorado due to compatibility changes brought by the constant evolution of the specifications of the truck and the drivers' need to receive similar performance features regardless of the vehicle's model year. Chevrolet Colorado is a compact to mid size pickup truck; those models are popular due to their durability and variation of usage. In the market of automobiles, ABS Control Module is the most appreciable and valuable item, which is designed elaborately to improve both performance and security. As seen, the strengths of this brand, Chevrolet Colorado ABS Control Module, has therefore become a precedent for many consumers to view this brand as suitable for use.

Chevrolet Colorado ABS Control Module Parts and Q&A

Control Module
19121732
Q: How to replace the ABS Control Module on Chevrolet Colorado?
A:
Install clean paper or shop towels on the ABS Control Module assembly before disconnecting its electrical connector. Move the connector to the Brake Booster position. Denatured alcohol enables cleaning of the master cylinder after which brake pipes must be extracted from the master cylinder to the ABS Control Module assembly while the rear brake pipe needs removing from its retainers at the cowl. Keep contaminants away from brake systems by installing rubber plugs into the brake pipes at the ABS Control Module assembly and master cylinder and brake pressure modulator valve (BPMV). Take out the ABS Control Module from your vehicle by removing its mounting nuts first then position the ABS Control Module in a dry and glove- and shop-towel-free area. The ABS Control Module needs to be positioned on its side while replacing the abs module assembly due to mounting screws which cannot be removed or break during repair. Uninstall the four mounting screws coupled with collars from the ABS Control Module and bpmv connection points while throwing away the previous pieces for new equipment. When positioning the abs module for rotation ensure that the bpmv remains facing upward and avoid misalignment of electrical connectors. The separation of ABS Control Module from bpmv should be done without any pry bar usage before discarding the solenoid plate and o-rings followed by a bpmv assembly cleaning process with dot-3 brake fluid and paper towels. Check for contamination and corrosion on solenoids and the bpmv assembly because you should replace it if necessary. The ABS Control Module assembly requires new solenoid plate and o-rings before connecting its bpmv attachment with new collars. Place mounting screws of the ABS Control Module under initial finger tightening then apply torque to 5 n.m (44 lb in). After that, attach the abs module to the vehicle and fasten the mounting nuts with a torque of 9 n.m (80 lb in). Put away rubber plugs at the brake pipe and ABS Control Module assembly site before you attach the brake pipes to the ABS Control Module assembly while tightening the fittings to 19 n.m (14 lb ft). Apply this procedure to the ABS Control Module assembly to master cylinder brake pipe installation. Attach the electrical connector while securing the rear brake pipe to its cowl retainer then pull out paper materials from within the ABS Control Module assembly interface and inner fender. The abs brake system needs bleeding before proceeding to control module reference materials which contain information about setup and replacement procedures.