How to replace the LH Motor and Transmission Mount on Chevrolet Cavalier?

To remove the left transmission mount, you shall remove the washer solvent container and raise the vehicle safety. Next, there are the left front wheel and tire assemblies that must be removed, followed by the left front fender liners being removed. To avoid the destruction of the Oil Pan bottom and the risk of engine military censorship, lay the hook that goes fully on the Oil Pan bottom's width between this Oil Pan and jack assurance. Setting under the transaxle a block of wood and a jack stand, pulling the transaxle mount through-bolt as well as the ones linking the transaxle to the engine block, and then the front transaxle mount. For installation, start by installing the front transaxle mount and its bolts in 75 nm (60 ft. Lbs.), and install the front transaxle mount through-bolt in 60 nm (44 ft. Lbs.). Before that, reinstall the left front fender liner the left front tire and wheel assembly, remove the jack stand, lower the vehicle, and the last thing taken off washer solvent container.

How to Service and Repair the Motor And Transmission Mount on a 3T40 Automatic Transaxle on Chevrolet Cavalier?

The 3t40 automatic transaxle transmission mount servicing and repair process starts with air intake duct removal then follows tv cable disconnection (when equipped) before removing the power brake booster line and hose. Use engine support fixture (J 28467-360) to lift the vehicle into position for support. Begin by taking out the engine mount strut along with the left front tire assembly, left splash shield and crossmember and left abs wheel speed sensor harness and connector from the suspension support. The work sequence includes removing the stabilizer shaft and left front Ball Joint from the left lower Control Arm followed by the front suspension support and left side drive axle from the transmission. Use plugs to seal off both transmission cooler pipes and p/s lines before removal. Sever the transmission mount to body bolts and pipe expansion bolt from the transmission support assembly. Place the engine and transmission assembly at a lowered position to remove both the transmission mount from the transmission support assembly then bolt the support assembly and finally remove the assembly itself. To install the transmission support assembly position it into the vehicle then bolt it into place and torque all bolts to 75 nm (55 ft. Lbs.). After mounting the transmission to the support assembly first raise the engine-transmission assembly then tighten its body bolts to 66 nm (49 ft. Lbs.). The transmission pipe expansion bolt needs installation onto the transmission support assembly with a torque setting of 55 nm (41 ft. Lbs.) before connecting the p/s lines to the p/s gear and the transmission cooler lines. The drive axle should be reinstalled on the transmission following installation of the front suspension support with the stabilizer shaft to the left lower Control Arm and left front Ball Joint. Install the left front abs wheel speed sensor before placing the crossmember in position along with the left splash shield, left front tire assembly and engine mount strut. Drop the vehicle and take out the engine support fixture (J 28467-360) while reestablishing the power brake booster line along with tv cable if present. Completion involves installing the air intake duct while you should adjust p/s oil levels and inspect transmission oil levels before checking for any oil leakage in the system.

OEM Chevrolet Cavalier Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Motor And Transmission Mounts found

View related parts
Chevrolet Cavalier Front Mount Part Number: 22697409
$129.15 MSRP: $203.20
You Save: $74.05 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Bracket; Motor Mount; Mount; Mount, Engine Mounting
- Replaces: 22661411
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Cavalier | Base, LS, LS Sport | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS
View related parts
Chevrolet Cavalier Upper Mount Part Number: 22146735
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Mount; Engine Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2002 Chevrolet Cavalier | Base, LS, LS Sport, RS | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS
View related parts
Chevrolet Cavalier Motor Mount Part Number: 22538728
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Torque Strut; Engine Mount Bracket; Mount Bracket; Engine Bracket; Front Mount; Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1994 Chevrolet Cavalier | Base, CL, CS, RS, Type-10, Z24 | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22565301
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Mount Bracket
- Replaces: 14074053, 22576129
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 Chevrolet Cavalier | Base, CL, CS, RS, Type-10
View related parts
Chevrolet Cavalier Motor Mount, Rear Part Number: 22637949
Product Specifications
- Other Name: Mount Assembly-Engine Rear; Engine Mount Torque Strut; Engine Mount Bracket; Cylinder Block; Rear Mount; Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting
- Position: Rear
- Replaces: 22638595, 22579308
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Chevrolet Cavalier | Base, CL, CS, RS, Type-10, VL | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22565312
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Mount Bracket; Transmission Mount Bracket; Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1989 Chevrolet Cavalier | Base, CS, RS, VL, Z24 | 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Chevrolet Cavalier Mount Bracket Part Number: 14089771
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Engine Bracket; Front Mount Bracket; Front Bracket
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994, 1988-1990 Chevrolet Cavalier | Base, RS, Z24 | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
View related parts
Chevrolet Cavalier Motor Mount Part Number: 22538730
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Torque Strut; Engine Mount Bracket; Cylinder Block; Front Mount; Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1994 Chevrolet Cavalier | Base, RS, VL | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS
View related parts
Chevrolet Cavalier Motor Mount Part Number: 22638594
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Engine Bracket; Rear Mount; Rear Bracket; Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting
- Replaces: 22579305, 22579307, 14074093
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1994 Chevrolet Cavalier | Base, CL, CS, RS, Type-10, Z24 | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22565313
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Mount Bracket; Transmission Mount Bracket; Front Mount; Mount
- Replaces: 22576137, 14089723, 22576141
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1994 Chevrolet Cavalier | Base, CS, RS, VL, Z24 | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
View related parts
Chevrolet Cavalier Transmission Mount, Blue Part Number: 22171740
Product Specifications
- Other Name: Mount Assembly-Transmission *Blue; Transfer Case Mount; Engine Mount; Mount, Transmission Mounting
- Replaces: 22171758
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chevrolet Cavalier | Base, LS, LS Sport, RS, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Upper Mount Part Number: 22145866
Product Specifications
- Other Name: Mount; Engine Mount Bracket; Engine Mount; Motor Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Cavalier | LS, Z24 | 4 Cyl 2.3 L GAS
View related parts
Chevrolet Cavalier Motor Mount Part Number: 22565308
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Transmission Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 Chevrolet Cavalier | Base, CL, CS, RS, Type-10, Z24 | 6 Cyl 2.8 L GAS
View related parts
Chevrolet Cavalier Transmission Mount, Rear Part Number: 22617128
Product Specifications
- Other Name: Mount Assembly-Transmission Rear; Manual Transmission Mount Bushing; Transmission Mount Bushing; Transfer Case Mount; Mount, Transmission Mounting
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Cavalier | Base, LS, LS Sport, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22617126
Product Specifications
- Other Name: Mount, Transmission Mounting; Transfer Case Mount
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Cavalier | Base, LS, LS Sport, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22112838
Product Specifications
- Other Name: Mount, Transmission Mounting; Manual Transmission Mount Bushing; Transmission Mount Bushing; Transfer Case Mount
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Cavalier | Base, LS, RS, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Transmission Mount Part Number: 22112837
Product Specifications
- Other Name: Mount, Transmission Mounting; Transfer Case Mount
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Cavalier | Base, LS, RS, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Upper Mount Part Number: 22174933
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Mount; Engine Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2002 Chevrolet Cavalier | LS, LS Sport, Z24 | 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Upper Mount Part Number: 22174932
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2002 Chevrolet Cavalier | LS, LS Sport, Z24 | 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cavalier Engine Bracket Part Number: 22575983
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount; Lower Mount Brace
- Position: Rear Upper Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2002 Chevrolet Cavalier | Base, LS, LS Sport, RS, Z24 | 4 Cyl 2.2 L BI-FUEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS

| Page 1 of 2 |Next >

1-20 of 33 Results

Chevrolet Cavalier Motor And Transmission Mount

Want to cut long-term maintenance and repair costs? Choose OEM Motor And Transmission Mount. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Cavalier parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Cavalier Motor And Transmission Mount includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Cavalier Motor And Transmission Mount is a perfect complement necessary for the further usage of the Chevrolet Cavalier Models. Also meant to firmly fix the transmission, this Motor And Transmission Mount plays the role of protecting the equipment from the disturbing vibrations from the engine while providing it with firm support to boost the performance of the vehicle. The Chevrolet Cavalier was first introduced in 1982 and has been a renowned compact car manufacturer with several models enhacing on this component. Depending on the actual setup of a car, a Chevrolet Cavalier might employ one or more Motor And Transmission Mounts, all custom made for proper positioning of the transmission and for effective dampening of vibrations. This is not only beneficial for the performance of the car but is also instrumental in increasing safety since alignment should be maintained and unnecessary wear and tear on other parts reduced. In the present market of automotive parts, the Chevrolet Cavalier Motor And Transmission Mount is probably one of the most sought after parts owing to its strong and rigid build as well as highly advanced designs and models for various models of the car. Due to its ability to fit in the different generations of the Chevrolet Cavalier, it could be said that this Motor And Transmission Mount is evidence of the company's mission to provide efficient cars. Finally the Chevrolet Cavalier Motor And Transmission Mount are essential components which create comfortable and safe driving and underlining the fact that the Chevrolet Cavalier is one of the most popular car models all over the world.

Chevrolet Cavalier Motor And Transmission Mount Parts and Q&A

Front Mount
22697409
Q: How to replace the LH Motor and Transmission Mount on Chevrolet Cavalier?
A:
To remove the left transmission mount, you shall remove the washer solvent container and raise the vehicle safety. Next, there are the left front wheel and tire assemblies that must be removed, followed by the left front fender liners being removed. To avoid the destruction of the Oil Pan bottom and the risk of engine military censorship, lay the hook that goes fully on the Oil Pan bottom's width between this Oil Pan and jack assurance. Setting under the transaxle a block of wood and a jack stand, pulling the transaxle mount through-bolt as well as the ones linking the transaxle to the engine block, and then the front transaxle mount. For installation, start by installing the front transaxle mount and its bolts in 75 nm (60 ft. Lbs.), and install the front transaxle mount through-bolt in 60 nm (44 ft. Lbs.). Before that, reinstall the left front fender liner the left front tire and wheel assembly, remove the jack stand, lower the vehicle, and the last thing taken off washer solvent container.
Upper Mount
22146735
Q: How to Service and Repair the Motor And Transmission Mount on a 3T40 Automatic Transaxle on Chevrolet Cavalier?
A:
The 3t40 automatic transaxle transmission mount servicing and repair process starts with air intake duct removal then follows tv cable disconnection (when equipped) before removing the power brake booster line and hose. Use engine support fixture (J 28467-360) to lift the vehicle into position for support. Begin by taking out the engine mount strut along with the left front tire assembly, left splash shield and crossmember and left abs wheel speed sensor harness and connector from the suspension support. The work sequence includes removing the stabilizer shaft and left front Ball Joint from the left lower Control Arm followed by the front suspension support and left side drive axle from the transmission. Use plugs to seal off both transmission cooler pipes and p/s lines before removal. Sever the transmission mount to body bolts and pipe expansion bolt from the transmission support assembly. Place the engine and transmission assembly at a lowered position to remove both the transmission mount from the transmission support assembly then bolt the support assembly and finally remove the assembly itself. To install the transmission support assembly position it into the vehicle then bolt it into place and torque all bolts to 75 nm (55 ft. Lbs.). After mounting the transmission to the support assembly first raise the engine-transmission assembly then tighten its body bolts to 66 nm (49 ft. Lbs.). The transmission pipe expansion bolt needs installation onto the transmission support assembly with a torque setting of 55 nm (41 ft. Lbs.) before connecting the p/s lines to the p/s gear and the transmission cooler lines. The drive axle should be reinstalled on the transmission following installation of the front suspension support with the stabilizer shaft to the left lower Control Arm and left front Ball Joint. Install the left front abs wheel speed sensor before placing the crossmember in position along with the left splash shield, left front tire assembly and engine mount strut. Drop the vehicle and take out the engine support fixture (J 28467-360) while reestablishing the power brake booster line along with tv cable if present. Completion involves installing the air intake duct while you should adjust p/s oil levels and inspect transmission oil levels before checking for any oil leakage in the system.