How to replace the Crankshaft Position Sensor on Chevrolet Camaro?

The first step to replace the Crankshaft Position Sensor requires vehicle elevation while providing support. Begin by disconnecting the crankshaft position (CKP) electrical connector followed by removing the crankshaft sensor bolt and sensor from its location. Place the new crankshaft position sensor while following fastener caution to prevent vehicle damage. Secure the sensor with the bolt then tighten it to 10 Nm (89 lb in) tension before connecting the CKP electrical connector . Finally, lower the vehicle.

How is the Crankshaft Position Sensor Variation Learn Procedure Performed on Chevrolet Camaro?

The Crankshaft position (CKP) system variation compensating values write to pcm non-volatile memory following a learn procedure execution when either p1336 is detected or the pcm and its associated components including engine and position sensor replace. Safe procedures require blocking the vehicle's drive wheels through parking brakes before beginning this operation. Decelerate by letting go of the throttle once the engine hits the second fuel cut off mark for controlled engine braking. The learn procedure remains disabled under two conditions: when the engine coolant temperature reaches below 70°c (158°F) and when the powertrain system displays any dtcs outside of dtc p1336. The learn function will be disabled if the camshaft position signal circuit experiences any fault or if either the 3x reference circuit or the 18x reference circuit shows a malfunction. Initiate parking brake activation along with wheel blockage and hood closure before starting the procedure. After engine start allow the coolant to achieve a temperature of at least 70°c (158°F) then turn off the ignition. Through the scan tool activate the Crankshaft position variation learn procedure then start the vehicle and apply service brake pressure until the transaxle enters park position. Steer the pedal until the system reaches 5,150 rpm for fuel cutoff before letting off pressure when the second cutoff occurs. During rpm recovery from the fuel cutoff point the rpm system acquires the required compensating parameters. Check vehicle dtc status for dtc p1336 following the complete procedure. The learn procedure completes when the test vehicle runs correctly. Probe p1336 once more following inspections for dtcs but execute the learn procedure again if p1336 remains the only dtc in the system.

OEM Chevrolet Camaro Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Crankshaft Position Sensors found

View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12703627
$60.13 MSRP: $107.38
You Save: $47.25 (44%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12585546
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | SS, Z/28, ZL1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12674702
$44.84 MSRP: $91.06
You Save: $46.22 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Camshaft Position Sensor; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12627185, 12632872
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2023 Chevrolet Camaro | LS, LT | 4 Cyl 2.0 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12669636
$28.91 MSRP: $54.30
You Save: $25.39 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12623094
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | LT1, SS, ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12646781
$14.45 MSRP: $27.14
You Save: $12.69 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | LS, LT | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12615626
$17.35 MSRP: $32.60
You Save: $15.25 (47%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | LS, LT | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 12560228
$66.20 MSRP: $119.82
You Save: $53.62 (45%)
ADD TO CART
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Engine Camshaft Position Sensor; Crankshaft Sensor
- Replaces: 12555566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 Chevrolet Camaro | Z28, Z28 SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 10456161
$86.13 MSRP: $174.94
You Save: $88.81 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Engine Crankshaft Position Sensor; Crankshaft Sensor; Position Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2002 Chevrolet Camaro | Base, RS | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 19170837
Product Specifications
- Other Name: Sensor Assembly, Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 10456534, 10456237
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Chevrolet Camaro | Z28 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Knock Sensor Part Number: 10456287
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Control Module; ESC Sensor; Sensor
- Replaces: 10456017
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Chevrolet Camaro | Z28 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 10137663
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 24503954
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Chevrolet Camaro | Base | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Camaro Crankshaft Position Sensor Part Number: 10456108
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Chevrolet Camaro | Base | 6 Cyl 3.4 L GAS

Chevrolet Camaro Crankshaft Position Sensor

Want to cut long-term maintenance and repair costs? Choose OEM Crankshaft Position Sensor. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Camaro parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Camaro Crankshaft Position Sensor includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Crankshaft Position Sensor in Chevrolet Camaro vehicles is a significant electronic that helps the car's engine to determine the crankshaft position as well as its rotational rate. This sensor sends vital signals to the powertrain control module and helps properly adjust ignition timing and fuel injection that are critical for a good engine function. Different types of CPS have been used in Chevrolet Camaro models, inductive, Hall Effect, magnetoresistive and optical sensors have been widely used. Inductive sensors are usually of a passive type and Hall Effect and magnetoresistive sensors are capable of detecting a static type of magnetic field. Optical sensors have a good ability to detect the edge but the problem is that they are more sensitive to fouling. The problems arise when the Crankshaft Position Sensor fails, this will lead to starting problems or stalling of the engine most especially under heat or vibration stress.

Chevrolet Camaro Crankshaft Position Sensor Parts and Q&A

Crankshaft Position Sensor
12615626
Q: How to replace the Crankshaft Position Sensor on Chevrolet Camaro?
A:
The first step to replace the Crankshaft Position Sensor requires vehicle elevation while providing support. Begin by disconnecting the crankshaft position (CKP) electrical connector followed by removing the crankshaft sensor bolt and sensor from its location. Place the new crankshaft position sensor while following fastener caution to prevent vehicle damage. Secure the sensor with the bolt then tighten it to 10 Nm (89 lb in) tension before connecting the CKP electrical connector . Finally, lower the vehicle.
Crankshaft Position Sensor
12560228
Q: How is the Crankshaft Position Sensor Variation Learn Procedure Performed on Chevrolet Camaro?
A:
The Crankshaft position (CKP) system variation compensating values write to pcm non-volatile memory following a learn procedure execution when either p1336 is detected or the pcm and its associated components including engine and position sensor replace. Safe procedures require blocking the vehicle's drive wheels through parking brakes before beginning this operation. Decelerate by letting go of the throttle once the engine hits the second fuel cut off mark for controlled engine braking. The learn procedure remains disabled under two conditions: when the engine coolant temperature reaches below 70°c (158°F) and when the powertrain system displays any dtcs outside of dtc p1336. The learn function will be disabled if the camshaft position signal circuit experiences any fault or if either the 3x reference circuit or the 18x reference circuit shows a malfunction. Initiate parking brake activation along with wheel blockage and hood closure before starting the procedure. After engine start allow the coolant to achieve a temperature of at least 70°c (158°F) then turn off the ignition. Through the scan tool activate the Crankshaft position variation learn procedure then start the vehicle and apply service brake pressure until the transaxle enters park position. Steer the pedal until the system reaches 5,150 rpm for fuel cutoff before letting off pressure when the second cutoff occurs. During rpm recovery from the fuel cutoff point the rpm system acquires the required compensating parameters. Check vehicle dtc status for dtc p1336 following the complete procedure. The learn procedure completes when the test vehicle runs correctly. Probe p1336 once more following inspections for dtcs but execute the learn procedure again if p1336 remains the only dtc in the system.