Should the ABS Control Module be repaired or replaced for safety reasons on Chevrolet Camaro?

The Brake Pressure Modulator Valve (BPMV) requires full replacement for safety reasons since no repair is allowed. The removal of screws from the EBCM/EBTCM is not permitted because it jeopardizes brake circuit leak-tightness and creates safety risks. The first step involves placing the ignition switch to OFF and removing the EBCM harness connector. Take note of how the brake pipes are positioned for assistance during installation before disconnecting the brake pipes from the BPMV. Remove the two nuts from the BPMV to BPMV bracket connection while using cap coverage to protect exterior surfaces from brake fluid damage to paint. The vehicle team should disconnect BPMV and EBCM as an assembly. Before installing a new BPMV users must remove the shipping plugs that are inserted into the valve opening. Place the BPMV together with EBCM assembly inside the BPMV bracket slot according to the specified mounting points. Fit the 2 BPMV bracket nuts and tighten them to 12 Nm (8 ft. lbs.). The successful operation of the brake pressure modulator valve demands proper pipe connection to the valve since wheel lockup can be detected through a Scan Tool or with an Antilock stop. Attach the brake pressure modulator valve (BPMV) pipes with proper torque at 15 Nm (11 ft. lbs.). Connect the EBCM harness connector before starting the engine with RUN selected position and complete the Diagnostic System Check - ABS. All air entry into the brake system requires execution of full bleeding procedures after brake component maintenance or replacement. Per the procedure one should bleed all components of the brake system.

How to remove and install the ABS Control Module on Chevrolet Camaro?

Begin the abs control module (ABSCM) removal process only when the ignition switch shows off to safeguard equipment. Unlock the tab on the abscm harness connector and then disconnect both the abscm harness connector and the pump motor connector that is found at the bottom of the abscm. Using caution to protect the solenoid valves and seal we will get rid of the six screws which connect abscm to bpmv and discard them. Separate the abscm from the bpmv with gentle force while making note of the wave spring position for the correct reinstall. System operations that include abs only require removal of one wave spring between abscm and bpmv but abs/tcs systems require removal of two wave springs that need to be discarded. Clean the bpmv gasket area on the surface by using alcohol poured onto a clean rag before installing. For systems with abs only use one wave spring at the identified abscm to bpmv interface; abs/tcs systems require two wave springs installed in the same way. Refitting the abscm to the bpmv starts with tightening the top four mounting screws to 2.9 Nm (26 inch lbs.) in an X pattern before securing the bottom two mounting screws to the same torque. The pump motor connector requires connection to the abscm's bottom end before applying the abscm harness connector with proper tab insertion. After switching off the ignition to the run position you must run the a diagnostic system check - abs.

OEM Chevrolet Camaro ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

47 ABS Control Modules found

View related parts
Chevrolet Camaro Control Module Part Number: 13513466
$298.62 MSRP: $594.03
You Save: $295.41 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; Parking Brake Control; Actuator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Camaro | LS, LT, LT1, SS, ZL1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 13501701
$422.30 MSRP: $840.15
You Save: $417.85 (50%)
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control
- Replaces: 92258052
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Camaro | LT, SS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 22966395
$536.28 MSRP: $1098.92
You Save: $562.64 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Camaro | Z/28 | 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 13509440
$315.37 MSRP: $627.37
You Save: $312.00 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; Parking Brake Control; Actuator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017 Chevrolet Camaro | LS, LT, SS, ZL1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 84166562
$320.42 MSRP: $629.38
You Save: $308.96 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018 Chevrolet Camaro | LS, LT, ZL1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 84452779
$197.69 MSRP: $371.24
You Save: $173.55 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2024 Chevrolet Camaro | LS, LT, LT1, SS, ZL1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Module Kit, Electronic Brake Control Part Number: 84940291
$249.48 MSRP: $468.50
You Save: $219.02 (47%)
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control
- Replaces: 84510235
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2024 Chevrolet Camaro | LT1, SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Modulator Valve Part Number: 84791033
$323.89 MSRP: $608.22
You Save: $284.33 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control (W/Brake Pressure Mode Valve); ABS Control Unit; Module, Electronic Brake Control
- Replaces: 23303422
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Camaro | LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Modulator Valve Part Number: 84244639
$392.54 MSRP: $737.16
You Save: $344.62 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; ABS Control Unit
- Replaced by: 84791024
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018 Chevrolet Camaro | LS, LT, SS, ZL1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Modulator Valve Part Number: 84940286
$424.07 MSRP: $796.38
You Save: $372.31 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Kit, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 84452770
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2024 Chevrolet Camaro | LS, LT, SS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 84820908
$543.79 MSRP: $1021.20
You Save: $477.41 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; Module; Module Kit, Electronic Brake Control
- Replaces: 84452780
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2024 Chevrolet Camaro | SS, ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Modulator Valve Part Number: 22966396
$787.13 MSRP: $1478.18
You Save: $691.05 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve, Brake Pressure Mode; Valve, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Camaro | Z/28 | 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 84121208
$167.01 MSRP: $302.28
You Save: $135.27 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017 Chevrolet Camaro | SS, ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 23303420
$212.61 MSRP: $384.81
You Save: $172.20 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Camaro | LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 84121202
$213.04 MSRP: $385.60
You Save: $172.56 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017 Chevrolet Camaro | LS, LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Modulator Valve Part Number: 84791032
$306.67 MSRP: $555.05
You Save: $248.38 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control (W/Brake Pressure Mode Valve); ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Replaces: 23303421, 84256032
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Camaro | SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 92242286
$638.36 MSRP: $1150.20
You Save: $511.84 (45%)
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2015 Chevrolet Camaro | LS, LT, SS, Z/28, ZL1 | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 92246446
$595.73 MSRP: $1069.60
You Save: $473.87 (45%)
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module
- Replaces: 92240018
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2011 Chevrolet Camaro | LS, LT, SS | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Motor Assembly Part Number: 18024455
Product Specifications
- Other Name: Motor Kit, Electronic Traction Control Brake Pressure Mode Valve; ABS Pump And Motor Assembly
- Replaces: 18021107
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Camaro | Base, RS, Z28 | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Control Module Part Number: 19302024
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; Module Kit, Electronic Brake Control
- Replaces: 12457657
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2002 Chevrolet Camaro | Z28, Z28 SS | 8 Cyl 5.7 L GAS

| Page 1 of 3 |Next >

1-20 of 47 Results

Chevrolet Camaro ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Camaro parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Camaro ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Camaro ABS Control Module is one of the critical systems or the anti-lock braking system commonly known for its durability and efficiency in different Chevrolet Camaro models. Serving as an upgraded and complex unit, this module serves as a vehicle safety and efficiency regulating tool that prevents wheel lock up during instances of heavy braking for precise vehicle control. Evolved wheel speed sensors assist the ABS Control Module to constantly read each wheel speed while valves and pumps control brake pressure to enhance grip of the road. This automation enables developers to achieve very high rater of execution of the braking techniques i.e grand acceleration and threshold and cadence braking among others which are beyond the physical capabilities of human controllers. Lately, the Chevrolet Camaro has been designed to have various improvements in the aspects of its ABS Control Module in that it has incorporated features such as ESC and traction control known for their ability to electronically control selective operations of the wheels as well as variations in braking force required during acceleration. As is the case with most of the ABS Control Modules the stopping distances, at least on most surfaces, are improved but the real advantage is the ability to steer the car, especially in the rough. The Chevrolet Camaro was manufactured between 1967 and 2002 and then reintroduced in 2010; it works with different engines, for example; V6 and V8 engine adding to its power. Incorporating powerful engines, responsive transmissions and a good interior design, Chevrolet Camaro ABS Control Module has well positioned the vehicle in the automobile market by leapfrogging the tradition by providing a splendid driving experience and of course upholding safe and efficient driving.

Chevrolet Camaro ABS Control Module Parts and Q&A

Modulator
10326058
Q: Should the ABS Control Module be repaired or replaced for safety reasons on Chevrolet Camaro?
A:
The Brake Pressure Modulator Valve (BPMV) requires full replacement for safety reasons since no repair is allowed. The removal of screws from the EBCM/EBTCM is not permitted because it jeopardizes brake circuit leak-tightness and creates safety risks. The first step involves placing the ignition switch to OFF and removing the EBCM harness connector. Take note of how the brake pipes are positioned for assistance during installation before disconnecting the brake pipes from the BPMV. Remove the two nuts from the BPMV to BPMV bracket connection while using cap coverage to protect exterior surfaces from brake fluid damage to paint. The vehicle team should disconnect BPMV and EBCM as an assembly. Before installing a new BPMV users must remove the shipping plugs that are inserted into the valve opening. Place the BPMV together with EBCM assembly inside the BPMV bracket slot according to the specified mounting points. Fit the 2 BPMV bracket nuts and tighten them to 12 Nm (8 ft. lbs.). The successful operation of the brake pressure modulator valve demands proper pipe connection to the valve since wheel lockup can be detected through a Scan Tool or with an Antilock stop. Attach the brake pressure modulator valve (BPMV) pipes with proper torque at 15 Nm (11 ft. lbs.). Connect the EBCM harness connector before starting the engine with RUN selected position and complete the Diagnostic System Check - ABS. All air entry into the brake system requires execution of full bleeding procedures after brake component maintenance or replacement. Per the procedure one should bleed all components of the brake system.
Control Module
19302024
Q: How to remove and install the ABS Control Module on Chevrolet Camaro?
A:
Begin the abs control module (ABSCM) removal process only when the ignition switch shows off to safeguard equipment. Unlock the tab on the abscm harness connector and then disconnect both the abscm harness connector and the pump motor connector that is found at the bottom of the abscm. Using caution to protect the solenoid valves and seal we will get rid of the six screws which connect abscm to bpmv and discard them. Separate the abscm from the bpmv with gentle force while making note of the wave spring position for the correct reinstall. System operations that include abs only require removal of one wave spring between abscm and bpmv but abs/tcs systems require removal of two wave springs that need to be discarded. Clean the bpmv gasket area on the surface by using alcohol poured onto a clean rag before installing. For systems with abs only use one wave spring at the identified abscm to bpmv interface; abs/tcs systems require two wave springs installed in the same way. Refitting the abscm to the bpmv starts with tightening the top four mounting screws to 2.9 Nm (26 inch lbs.) in an X pattern before securing the bottom two mounting screws to the same torque. The pump motor connector requires connection to the abscm's bottom end before applying the abscm harness connector with proper tab insertion. After switching off the ignition to the run position you must run the a diagnostic system check - abs.