Why is it crucial to inspect and repair the seat belt system after a collision on Chevrolet Blazer?

Inspection and repair of seat belts system should happen immediately after a collision to guarantee safety. Seat belts must be replaced whenever automatic restraint devices deploy because of the vehicle collision. Automatic restraint devices include air bags and seat belt pretensioners. The inspection process covers both adult passenger seat belts together with all components necessary for child safety including latch system and top tether anchorages. It is necessary to replace all seat belt system components which show evidence of damage or wear or have tears including adult seat belts, integrated child restraints and latch system parts. A seat belt system needs replacement when either "replace" or "caution" appears on a label or when a yellow sign is present but not because a child seat caution sign is visible. A seat belt system replacement becomes necessary when there exists any doubt about its condition as it requires replacement of all components for adult seat belts and built-in child restraints and latch systems. The whole seat belt system requires replacement starting with the buckle followed by the guide and retractor assembly and finishing with the latch while webbing material as an integrated replacement rather than component replacement. The requirement for replacement depends on whether parts reveal tears or wear or damage after minor collisions which did not activate automatic restraint devices.

How to replace the front seat belt on Chevrolet Blazer?

Start front seat belt replacement by taking out the bolt which maintains the lower seat belt anchor plate attached to the vehicle. Apply a flat-bladed tool to open the upper seat belt anchor plate cover carefully before removing the bolt that maintains the upper seat belt anchor plate. To start you should uninstall the body side trim panel while you guide the seat belt through its corresponding opening in the body side trim cover. Extract the bolt which maintains the seat belt retractor assembly before removing the assembly from the vehicle. Reinstall the seat belt retractor assembly into the vehicle by using the bolt securing process at 70 N.m (52 lb ft). League the seat belt through the body side trim cover opening before replacing the body side trim panel on the vehicle. Start by pressing the seat belt opening trim cover tightly against its position before adding the upper seat belt anchor plate along with bolt installation at 70 N.m (52 lb ft). Secure the lower seat belt anchor plate together with its bolt at 70 N.m (52 lb ft) torque value.

OEM Chevrolet Blazer Seat Belt

Seat Safety Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

32 Seat Belts found

View related parts
Chevrolet Blazer Buckle End, Passenger Side Part Number: 12474640
$57.27 MSRP: $81.95
You Save: $24.68 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Kit, Passenger Seat (Buckle Side) *Graphite
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Front Passenger Side Part Number: 12380608
$39.42 MSRP: $70.00
You Save: $30.58 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Kit, A52- Front Bench
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Blazer | Base, LS, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Center Seat Belt, Front Driver Side Part Number: 12477774
$59.99 MSRP: $89.28
You Save: $29.29 (33%)
ADD TO CART
Product Specifications
- Other Name: Belt Kit, A52- Front Bench
- Position: Front Center Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2005 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Buckle End, Jet Black Part Number: 86802084
$77.69 MSRP: $115.64
You Save: $37.95 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Buckle Kit-Front Seat Belt * Jet Black
- Replaced by: 85652156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2025 Chevrolet Blazer | Base, L, LT, Premier, RS | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Jet Black Part Number: 86802058
$104.88 MSRP: $156.10
You Save: $51.22 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Retractor Kit-Rear Seat Center Belt *Jet Black
- Replaces: 19352449, 19367122, 84826212, 84572067
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2025 Chevrolet Blazer | Base, L, LT, Premier, RS | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Blazer Belt & Retractor Part Number: 89023941
$56.13 MSRP: $81.68
You Save: $25.55 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Passenger Side
- Replaces: 12477784, 88898889
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chevrolet Blazer | LS, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Belt & Retractor Part Number: 89023939
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Driver Side
- Replaces: 12470359, 12474511, 12477783, 88898888
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chevrolet Blazer | LS, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Center Seat Belt Part Number: 89023948
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Center
- Replaces: 12377017, 12477779, 12474662
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Blazer | Base, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Buckle End Part Number: 88951000
Product Specifications
- Other Name: Belt Kit, Driver Seat (Buckle Side) *Graphite; Outer Buckle; Buckle; Latch
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Blazer | Base, LS, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt Part Number: 89023933
Product Specifications
- Other Name: Belt Kit, Passenger Seat (Retractor Side) *Graphite *Graphite
- Position: Passenger Side
- Replaces: 12470354, 12474110, 12477759, 88898882, 88955921
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2005 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Rear Seat, Driver Side Part Number: 20626874
Product Specifications
- Other Name: Belt
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1991 Chevrolet Blazer | Custom Deluxe, Scottsdale, Silverado | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
Chevrolet Blazer Buckle End, Driver Side Part Number: 12474639
Product Specifications
- Other Name: Belt Kit, Driver Seat (Buckle Side) *Graphite
- Position: Driver Side
- Replaces: 12470428
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Center Seat Belt, Rear Passenger Side Part Number: 12477780
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Passenger Side
- Replaces: 12474657, 12474748
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Blazer | LS, LT, Trailblazer, Xtreme | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap Belt, Blue Part Number: 12522529
Product Specifications
- Other Name: Belt Kit, Seat Belt; Water Pump; Water Pump Assembly; Center Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet Blazer | Base, Cheyenne, Silverado, Silverado Sport | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Rear Passenger Side Part Number: 12388658
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench; Belt & Retractor; Belt Kit, A52 - Front Bench
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Blazer | Base, LS, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Rear Passenger Side Part Number: 12375466
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Seat
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Blazer | Base, LS, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Beige Part Number: 12375461
Product Specifications
- Other Name: Belt Kit, Driver Seat *Beige
- Position: Passenger Side
- Replaces: 12381813, 12387505
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Blazer | Base, LS, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Beige Part Number: 12375454
Product Specifications
- Other Name: Belt Kit, Passenger Seat *Beige
- Position: Driver Side
- Replaces: 12381814, 12387498
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Blazer | Base, LS, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Center Seat Belt, Front Part Number: 12380610
Product Specifications
- Other Name: Belt Kit, Am6- Front Split Bench; Belt Kit, Am6 - Front Split Bench
- Position: Front Center
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Blazer | Base, LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Blazer Lap & Shoulder Belt, Gray, Driver Side Part Number: 12380483
Product Specifications
- Other Name: Belt Kit, Driver Seat (Retractor Side) Gray
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet Blazer | Base, Cheyenne, Silverado, Silverado Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL

| Page 1 of 2 |Next >

1-20 of 32 Results

Chevrolet Blazer Seat Belt

Want to cut long-term maintenance and repair costs? Choose OEM Seat Belt. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Blazer parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Blazer Seat Belt includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Blazer Seat Belt Parts and Q&A

Center Seat Belt, Front Driver Side
12477774
Q: Why is it crucial to inspect and repair the seat belt system after a collision on Chevrolet Blazer?
A:
Inspection and repair of seat belts system should happen immediately after a collision to guarantee safety. Seat belts must be replaced whenever automatic restraint devices deploy because of the vehicle collision. Automatic restraint devices include air bags and seat belt pretensioners. The inspection process covers both adult passenger seat belts together with all components necessary for child safety including latch system and top tether anchorages. It is necessary to replace all seat belt system components which show evidence of damage or wear or have tears including adult seat belts, integrated child restraints and latch system parts. A seat belt system needs replacement when either "replace" or "caution" appears on a label or when a yellow sign is present but not because a child seat caution sign is visible. A seat belt system replacement becomes necessary when there exists any doubt about its condition as it requires replacement of all components for adult seat belts and built-in child restraints and latch systems. The whole seat belt system requires replacement starting with the buckle followed by the guide and retractor assembly and finishing with the latch while webbing material as an integrated replacement rather than component replacement. The requirement for replacement depends on whether parts reveal tears or wear or damage after minor collisions which did not activate automatic restraint devices.
Lap & Shoulder Belt
89023933
Q: How to replace the front seat belt on Chevrolet Blazer?
A:
Start front seat belt replacement by taking out the bolt which maintains the lower seat belt anchor plate attached to the vehicle. Apply a flat-bladed tool to open the upper seat belt anchor plate cover carefully before removing the bolt that maintains the upper seat belt anchor plate. To start you should uninstall the body side trim panel while you guide the seat belt through its corresponding opening in the body side trim cover. Extract the bolt which maintains the seat belt retractor assembly before removing the assembly from the vehicle. Reinstall the seat belt retractor assembly into the vehicle by using the bolt securing process at 70 N.m (52 lb ft). League the seat belt through the body side trim cover opening before replacing the body side trim panel on the vehicle. Start by pressing the seat belt opening trim cover tightly against its position before adding the upper seat belt anchor plate along with bolt installation at 70 N.m (52 lb ft). Secure the lower seat belt anchor plate together with its bolt at 70 N.m (52 lb ft) torque value.