How to service and repair the front wheel bearing and hub on Cadillac Seville?

To fix the front wheel hub and bearing set up you need to first raise the vehicle and support it with the frame while allowing the suspension components to hang free. Use a wheel wrench to remove the wheel before you turn the wheel drive shaft nut using a drift punch tool. Unplug the front wheel speed sensor connector from its dust shield and take off both the rotor and its bearing unit. Start repair by taking out the dust shield and bearing retaining bolts then set the transmission to park position. Use wheel hub remover (J 28733-B) to detach the axle drive components while keeping the hub and bearing unit a single replacement part. Wash off all dirt and rust that might prevent the bearing from fitting into the knuckle mounting face and bore. Fit the hub set onto the drive axle and spread grease inside the knuckle bore while removing the plastic cover from the new components before assembly. Do not touch the knuckle or hub assembly through its abs sensor electrical wire. Add the new axle nut then push the hub with bearing onto the axle and put the transmission into neutral position. Install the dust shield with care to keep the bearing's outside seal safe then use a torque wrench to fix the hub and bearing bolts to 130 nm (95 ft. Lbs.). Link the wheel sensor connector and pin it to the dust shield position. Insert the rotor when the wheel drive shaft gets tightened to 160 nm (118 ft. Lbs) using low-turn prevention tools such as a drift punch or screwdriver. Put on the wheel and tire then lower the car carefully.

How to replace the front wheel bearing and hub on Cadillac Seville?

Start the hub bearing replacement by lifting the vehicle above the ground. Put a drift punch through the brake components to keep the rotor locked when removing the wheel nut and tire. First disconnect the power from the front Wheel Speed Sensor and unfasten it from the dust shield before taking out the brake rotor. Before continuing disassembly of the brake assembly take off both monitoring sensors if your vehicle includes them. Take out the dust shield and hub retaining bolts along with Wheel Bearing. Keep track that only the complete Wheel Bearing and hub replacement is necessary. Separate the Wheel Bearing and hub from the drive axle by using the wheel hub remover (J28733-B). Afterwards remove the Wheel Bearing, hub, and dust shield as a single piece. You should wash away all rust and unwanted particles from the knuckle mounting surface, bore, and chamber to make room for a good fit between the bearing and knuckle. Mount the Wheel Bearing and hub assembly over the drive axle with dust shield while spreading a light amount of grease on the Steering Knuckle bore and keep the abs sensor wire free from contact. Apply new axle nut and push hub with bearing onto drive axle. Place Wheel Bearing and hub bolt in place and tighten it to 130 nm (95 ft. Lbs.). Replace the speed sensor electric connections to the dust shield for both simple and indicator sensors. Climb the brake rotor for fitting before you tighten the wheel drive shaft nut to 145 nm (107 ft. Lbs.) while a drift punch or a screwdriver controls the rotor from moving. Lower the vehicle over the wheel and position the tire before completing installation.

OEM Cadillac Seville Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Wheel Bearings found

View related parts
Cadillac Seville Front Hub & Bearing Assembly Part Number: 7470511
$199.93 MSRP: $361.87
You Save: $161.94 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Hub & Bearing; Hub & Bearing Assembly; Rotor Hub & Bearing; Hub
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Hub Assembly, Front Part Number: 84641365
$210.54 MSRP: $412.24
You Save: $201.70 (49%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Assembly, Front Wheel (W/Wheel Speed Sensor); Front Hub & Bearing; Front Wheel Hub Kit; Rear Wheel Hub
- Position: Front
- Replaced by: 19433930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Hub Assembly, Front Part Number: 12429204
$210.54 MSRP: $412.24
You Save: $201.70 (49%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Kit, Front Wheel; Wheel Bearing & Hub Assembly; Disc Brake Hardware Kit; Wheel Hub Repair Kit; Axle Bearing.; Front Hub & Bearing; Front Hub; Hub & Bearing; Hub Kit, Rear Wheel
- Position: Front
- Replaced by: 19433930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2000 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Hub Assembly, Rear Part Number: 7470555
Product Specifications
- Other Name: Hub, Rear Wheel (W/Wheel Speed Sensor); Wheel Bearing & Hub Assembly; Axle Bearing.; Rear Hub & Bearing Assembly; Hub & Bearing; Hub & Bearing Assembly; Rotor Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004, 1992 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Hub Assembly, Rear Part Number: 7470543
Product Specifications
- Other Name: Hub, Rear Wheel; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub; Rear Hub & Bearing Assembly; Hub & Bearing; Rotor Hub & Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Hub & Bearing, Rear Outer Part Number: 7470539
Product Specifications
- Other Name: Bearing Assembly, Rear Brake Hub Outer; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Hub
- Position: Rear Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Front Hub & Bearing Part Number: 7466961
Product Specifications
- Other Name: Hub Assembly; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing
- Replaced by: 7470585
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Hub & Bearing Assembly Part Number: 7466949
Product Specifications
- Other Name: Hub Assembly; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing
- Replaced by: 12413025
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Cadillac Seville | Base, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Hub & Bearing, Front Part Number: 7470585
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Hub & Bearing Assembly; Rotor Hub & Bearing; Hub, Front Wheel
- Position: Front
- Replaces: 7466961
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Wheel Bearing, Rear Part Number: 7470503
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Hub Assembly; Bearing Assembly; Rear Bearing; Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Front Hub & Bearing Part Number: 7470005
Product Specifications
- Other Name: Hub Kit, Front Wheel; Wheel Bearing & Hub Assembly; Wheel Hub Repair Kit; Axle Bearing.; Front Hub; Hub & Bearing; Hub
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac Seville Wheel Bearing, Front Part Number: 7470003
Product Specifications
- Other Name: Hub, Front Wheel (W/Bearing); Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Front Wheel Bearing; Hub & Bearing Assembly; Rear Hub Bearings; Rotor Hub & Bearing.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1988 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Wheel Bearing, Rear Part Number: 12413025
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Rear Hub & Bearing Assembly; Hub & Bearing; Rotor Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Replaces: 7470579, 07470579, 7466949
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS

Cadillac Seville Wheel Bearing

Want to cut long-term maintenance and repair costs? Choose OEM Wheel Bearing. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Seville parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Seville Wheel Bearing includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Cadillac Seville Wheel Bearing is well understood in the range as an element that defines the stance of the brand as far as reliability and performance are concerned. Specifically intended for the proper rotation of the wheel, Cadillac Seville vehicles employ the Wheel Bearing in order to improve the vehicle's efficiency and safety. These Wheel Bearings are designed to suit several different models of Seville that were manufactured between 1975 and 2004 These WH wheel bearings provide minimum friction and thereby let the wheel and tire assembly run smoothly. Cadillac Seville can be equipped with three types of the hub and bearing assembly; the standard, the taper, and the pressed, the latter may also contain the sensor of an ABS system for security needs. Routine check or servicing or the Wheel Bearing is very important since damaged or loosened bearings may cause problem that include noise, vibration, or in extreme cases, separation of the wheel. The Cadillac Seville's development changes, such as for instance the dual-area autopilot climate control system together with traction control system, enhances the accessibility of its Wheel Bearings to deliver a luxurious ride. Specifically, Cadillac Seville Wheel Bearing is appreciated in the market for automobile as it is designed with a high level of solidity and has a sophisticated technology applied to improve the performance of the car. Thus, by addressing the issue of the Wheel Bearing as a priority, Cadillac Seville owners can guarantee the proper functioning of this part, which underlines the car's safety and solidity on the roadway.

Cadillac Seville Wheel Bearing Parts and Q&A

Hub Assembly, Front
12429204
Q: How to service and repair the front wheel bearing and hub on Cadillac Seville?
A:
To fix the front wheel hub and bearing set up you need to first raise the vehicle and support it with the frame while allowing the suspension components to hang free. Use a wheel wrench to remove the wheel before you turn the wheel drive shaft nut using a drift punch tool. Unplug the front wheel speed sensor connector from its dust shield and take off both the rotor and its bearing unit. Start repair by taking out the dust shield and bearing retaining bolts then set the transmission to park position. Use wheel hub remover (J 28733-B) to detach the axle drive components while keeping the hub and bearing unit a single replacement part. Wash off all dirt and rust that might prevent the bearing from fitting into the knuckle mounting face and bore. Fit the hub set onto the drive axle and spread grease inside the knuckle bore while removing the plastic cover from the new components before assembly. Do not touch the knuckle or hub assembly through its abs sensor electrical wire. Add the new axle nut then push the hub with bearing onto the axle and put the transmission into neutral position. Install the dust shield with care to keep the bearing's outside seal safe then use a torque wrench to fix the hub and bearing bolts to 130 nm (95 ft. Lbs.). Link the wheel sensor connector and pin it to the dust shield position. Insert the rotor when the wheel drive shaft gets tightened to 160 nm (118 ft. Lbs) using low-turn prevention tools such as a drift punch or screwdriver. Put on the wheel and tire then lower the car carefully.
Hub Assembly, Front
84641365
Q: How to replace the front wheel bearing and hub on Cadillac Seville?
A:
Start the hub bearing replacement by lifting the vehicle above the ground. Put a drift punch through the brake components to keep the rotor locked when removing the wheel nut and tire. First disconnect the power from the front Wheel Speed Sensor and unfasten it from the dust shield before taking out the brake rotor. Before continuing disassembly of the brake assembly take off both monitoring sensors if your vehicle includes them. Take out the dust shield and hub retaining bolts along with Wheel Bearing. Keep track that only the complete Wheel Bearing and hub replacement is necessary. Separate the Wheel Bearing and hub from the drive axle by using the wheel hub remover (J28733-B). Afterwards remove the Wheel Bearing, hub, and dust shield as a single piece. You should wash away all rust and unwanted particles from the knuckle mounting surface, bore, and chamber to make room for a good fit between the bearing and knuckle. Mount the Wheel Bearing and hub assembly over the drive axle with dust shield while spreading a light amount of grease on the Steering Knuckle bore and keep the abs sensor wire free from contact. Apply new axle nut and push hub with bearing onto drive axle. Place Wheel Bearing and hub bolt in place and tighten it to 130 nm (95 ft. Lbs.). Replace the speed sensor electric connections to the dust shield for both simple and indicator sensors. Climb the brake rotor for fitting before you tighten the wheel drive shaft nut to 145 nm (107 ft. Lbs.) while a drift punch or a screwdriver controls the rotor from moving. Lower the vehicle over the wheel and position the tire before completing installation.