How to service and repair the steering knuckle for RPO FE7 on Cadillac DeVille?

To service and repair Steering Knuckle for rpo fe7, one has to raise the vehicle and remove the wheel and tire. Then, take the cotter pin and nut off the lower Ball Joint, along with the wheel drive shaft nut, and, finally, remove the brake caliper bolts. Deposits the caliper away from the driving wheel, and has the rotor removed. Remove the wheel speed sensor connector and remove the hub and bearing retaining bolts. Use hub and bearing puller (J28733-B) to remove the hub and drive axle, and steering linkage and Tie Rod puller (J24319-B) to remove the Tie Rod from the Steering Knuckle. The lower arm, use the Ball Joint separator (j39549) to remove the ball joints from the Control Arm, then use the nuts and bolts to take the Steering Knuckle here from the strut to knuckle. The Steering Knuckle shall be attached to the strut, screwed to a tight strut to knuckle bolts 177 nm (131 ft. Lbs.). Install a new lower Ball Joint by connecting it, and tighten the Ball Joint stud nut to 30 nm (22 ft. Lbs.) with an extra 190 degrees, and install a new coter pin. Screw on the Tie Rod and tighten the Tie Rod end to knuckle nut to 30 nm (22 ft. Lbs.) plus 200 more degrees while making sure the cotter pin will be aligned, without backing off the nut. New hub and bearing install to Steering Knuckle/drive axle and install hub and bearing retaining bolts to 152 nm (112 ft. Lbs.). Reconnect the wheel speed sensor connector, rotor, followed by the caliper. Lastly, replace the drive axle nut by torquing it to 215 nm or 159 ft. Lbs. And wheel and tire which is torqued to 125 nm or 80 ft. Lbs. Check the wheel alignment as the final step of the process.

How to replace the steering knuckle for RPO FE1 and FE3 on Cadillac DeVille?

Replacing the Steering Knuckle needs the proper sequence of steps starting with vehicle lift and wheel and tire removal then Wheel Bearing and hub separation. Start by breaking all connections between the lower Ball Joint cotter pin and retaining nut and the outer tie rod retaining nut. Start by using the steering linkage and tie rod puller (J 24319-B) on the outer tie rod then use the Ball Joint separator (J 43828) to disconnect the Ball Joint from the Steering Knuckle. After removing all nuts and bolts which hold the Steering Knuckle to the strut, remove the Steering Knuckle itself. The installation involves positioning the Steering Knuckle between the lower Ball Joint and strut while correctly tightening all strut retaining fasteners. Secure Steering Knuckle to strut retaining nuts to 147 nm (108 ft. Lbs.), subsequently torque the lower Ball Joint retaining nut to 10 nm (88 inch lbs.) while turning it an additional 150° to achieve correct cotter pin alignment. Maintain the nut torque up to a maximum of 60° additional rotation before final tightening. You should install a new cotter pin before mounting the outer tie rod to the Steering Knuckle while tightening the outer tie rod retaining nut to 30 nm (22 ft. Lbs.) and adding an additional 180° rotation. To complete the procedure reinstall the Wheel Bearing and hub assembly as well as the tire and wheel then verify wheel alignment.

OEM Cadillac DeVille Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Steering Knuckles found

View related parts
Cadillac DeVille Knuckle, Driver Side Part Number: 23127629
$268.88 MSRP: $442.93
You Save: $174.05 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering (Machining); Knuckle, Steering
- Position: Driver Side
- Replaces: 18060638, 18060652, 88955418, 10434254, 18060680, 20899802, 25816684, 22990752
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2000 Cadillac DeVille | Base, Concours, d'Elegance, DHS, DTS | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Knuckle, Driver Side Part Number: 18016207
$205.86 MSRP: $299.00
You Save: $93.14 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle Part Number: 14012589
Product Specifications
- Other Name: Spindle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Lower Control Arm, Driver Side Part Number: 18021052
Product Specifications
- Other Name: Knuckle, Steering; Control Arm; Steering Knuckle; Knuckle
- Position: Driver Side
- Replaces: 18016023
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Lower Control Arm, Passenger Side Part Number: 18021053
Product Specifications
- Other Name: Knuckle, Steering; Control Arm; Steering Knuckle; Knuckle
- Position: Passenger Side
- Replaces: 18016024
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Steering Knuckle, Driver Side Part Number: 14012595
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Steering Knuckle, Passenger Side Part Number: 14012596
Product Specifications
- Other Name: Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Cadillac DeVille | Base, Cabriolet, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac DeVille Steering Knuckle, Passenger Side Part Number: 18060587
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Passenger Side
- Replaces: 18016759
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Cadillac DeVille | Base, Concours | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Steering Knuckle, Driver Side Part Number: 18060586
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Driver Side
- Replaces: 18016758
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Cadillac DeVille | Base, Concours | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Passenger Side Part Number: 18021750
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaced by: 88955417
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Knuckle, Driver Side Part Number: 18021749
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaced by: 88955416
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Knuckle, Passenger Side Part Number: 18060584
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 18016750
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac DeVille | Base, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Driver Side Part Number: 18060604
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 18020766
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Passenger Side Part Number: 18060605
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 18020767
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Rear Driver Side Part Number: 18026759
Product Specifications
- Other Name: Knuckle Assembly, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 18023711
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Knuckle, Rear Driver Side Part Number: 18026757
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 18023709, 18021056
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Rear Passenger Side Part Number: 18026758
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaces: 18021057, 18023710, 18017713
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Spindle, Rear Passenger Side Part Number: 25527482
Product Specifications
- Other Name: Knuckle, Rear Wheel; Knuckle
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1992 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Spindle, Rear Driver Side Part Number: 25527483
Product Specifications
- Other Name: Knuckle, Rear Wheel; Knuckle
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1992 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Knuckle, Driver Side Part Number: 18016011
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS

| Page 1 of 2 |Next >

1-20 of 33 Results

Cadillac DeVille Steering Knuckle

Want to cut long-term maintenance and repair costs? Choose OEM Steering Knuckle. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac DeVille parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac DeVille Steering Knuckle includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Steering Knuckle of Cadillac DeVille cars is relevant part that lies between the suspension and the steering systems of the car that rotates the wheels steadily. Originally, there are different types of Knuckles depending on the option which can be rear-wheel drive or front/all-wheel/four-wheel drive. While in rear-wheel drive vehicles may feature the spindle in the Knuckle, the drive axle penetrates through the Knuckle in the case of front/all-wheel/four-wheel drive vehicles. The kingpin, from which The Knuckle evolved, was utilized in the early types of automotive suspensions, particular to the leaf spring suspended beam axles before the use of ball joints. Steering Knuckles are strong parts and just need replacement if they got damaged; spindle check is done during service.

Cadillac DeVille Steering Knuckle Parts and Q&A

Knuckle, Driver Side
23127629
Q: How to service and repair the steering knuckle for RPO FE7 on Cadillac DeVille?
A:
To service and repair Steering Knuckle for rpo fe7, one has to raise the vehicle and remove the wheel and tire. Then, take the cotter pin and nut off the lower Ball Joint, along with the wheel drive shaft nut, and, finally, remove the brake caliper bolts. Deposits the caliper away from the driving wheel, and has the rotor removed. Remove the wheel speed sensor connector and remove the hub and bearing retaining bolts. Use hub and bearing puller (J28733-B) to remove the hub and drive axle, and steering linkage and Tie Rod puller (J24319-B) to remove the Tie Rod from the Steering Knuckle. The lower arm, use the Ball Joint separator (j39549) to remove the ball joints from the Control Arm, then use the nuts and bolts to take the Steering Knuckle here from the strut to knuckle. The Steering Knuckle shall be attached to the strut, screwed to a tight strut to knuckle bolts 177 nm (131 ft. Lbs.). Install a new lower Ball Joint by connecting it, and tighten the Ball Joint stud nut to 30 nm (22 ft. Lbs.) with an extra 190 degrees, and install a new coter pin. Screw on the Tie Rod and tighten the Tie Rod end to knuckle nut to 30 nm (22 ft. Lbs.) plus 200 more degrees while making sure the cotter pin will be aligned, without backing off the nut. New hub and bearing install to Steering Knuckle/drive axle and install hub and bearing retaining bolts to 152 nm (112 ft. Lbs.). Reconnect the wheel speed sensor connector, rotor, followed by the caliper. Lastly, replace the drive axle nut by torquing it to 215 nm or 159 ft. Lbs. And wheel and tire which is torqued to 125 nm or 80 ft. Lbs. Check the wheel alignment as the final step of the process.
Knuckle, Driver Side
19303855
Q: How to replace the steering knuckle for RPO FE1 and FE3 on Cadillac DeVille?
A:
Replacing the Steering Knuckle needs the proper sequence of steps starting with vehicle lift and wheel and tire removal then Wheel Bearing and hub separation. Start by breaking all connections between the lower Ball Joint cotter pin and retaining nut and the outer tie rod retaining nut. Start by using the steering linkage and tie rod puller (J 24319-B) on the outer tie rod then use the Ball Joint separator (J 43828) to disconnect the Ball Joint from the Steering Knuckle. After removing all nuts and bolts which hold the Steering Knuckle to the strut, remove the Steering Knuckle itself. The installation involves positioning the Steering Knuckle between the lower Ball Joint and strut while correctly tightening all strut retaining fasteners. Secure Steering Knuckle to strut retaining nuts to 147 nm (108 ft. Lbs.), subsequently torque the lower Ball Joint retaining nut to 10 nm (88 inch lbs.) while turning it an additional 150° to achieve correct cotter pin alignment. Maintain the nut torque up to a maximum of 60° additional rotation before final tightening. You should install a new cotter pin before mounting the outer tie rod to the Steering Knuckle while tightening the outer tie rod retaining nut to 30 nm (22 ft. Lbs.) and adding an additional 180° rotation. To complete the procedure reinstall the Wheel Bearing and hub assembly as well as the tire and wheel then verify wheel alignment.