How to replace the Hazard Warning Switch and Turn Signal Switch on Buick Century?

Begin switch replacement only when you see the lever centered at off position and cut off the battery's negative side. Turn off the sir before taking out the Steering Wheel and steering column decorative panels. Disconnect wire harness straps from the column assembly and remove the multifunction, turn signal, and hazard switch assembly connector from its connection to the sir coil assembly. Take out the multifunction switch assembly from the steering column by unplugging the bulkhead connectors and serving the switch assembly supports. Separate the steering column tilt head assembly from its multifunction and hazard switch unit. Use a small flat-port tool to push down the electrical contact and set the control switch on top of the steering column. Ensure that the electrical contact rests lightly on the turn signal cancellation cam. Turn the screws to 7 nm (62 inch lbs.) as you join the switch assembly connectors to both the steering column bulkhead and sir coil assembly connectors. Connect the wire harness assembly back to its position on the steering column supports, make sure the lever remains off, and put on the steering column trim panels and Steering Wheel. Reenable the sir system after reconnecting the battery's negative terminal.

How to remove and install the Turn Signal Switch on Buick Century?

Begin the multifunction turn signal lever removal procedure by placing the lever at the off position center and disconnecting the negative Battery Cable and disabling the sir system. The first step requires removal of the inflatable restraint Steering Wheel module followed by unstalling of the Steering Wheel while performing the same procedure for the steering column trim covers. Use heat shrinks to detach the steering column wire harness from its retainer then unfasten the two wire harness straps from the wire harness. Disconnect the steering column bulkhead connector from both the vehicle wire harness and the gray and black connectors from the multifunction turn signal lever steering column bulkhead connector. Start by removing bolts from the multifunction turn signal lever and move the lever out of the steering column. Installation of the multifunction turn signal lever requires using a small flat-blade to compress electrical contacts placing them on the canceling cam prior to positioning the lever in its original spot. Secure the multifunction turn signal lever with bolts and tighten each one to 6 nm (53 inch lbs.). Set the gray and black connectors into position with the multifunction turn signal lever steering column bulkhead connector before finalizing the connection between this bulkhead connector and the vehicle wire harness. Return the steering column wire harness into its retaining piece then fasten the straps from the wire harness onto it. After installing the steering column trim cover check that the lever points to center position or off and reinstall the Steering Wheel with the inflatable restraint Steering Wheel module. Reconnect the negative Battery Cable after enabling the sir system.

OEM Buick Century Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Turn Signal Switches found

View related parts
Buick Century Turn Signal Switch Part Number: 88963625
$331.20 MSRP: $518.32
You Save: $187.12 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Switch; Combination Switch; Switch, Windshield Wiper Control; Switch, Turn Signal Lamp; Switch, Headlamp Dimmer
- Replaces: 26081121, 26085929, 26067715
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Buick Century | Custom, Limited | 6 Cyl 3.1 L GAS
View related parts
Buick Century Signal Lever, Black Part Number: 19244690
$129.37 MSRP: $193.42
You Save: $64.05 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Turn Signal Control; Engagement Switch; Turn/Wiper Lever; Lever
- Replaces: 25111262
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1988 Buick Century | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 88964579
$161.21
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Switch; Combination Switch
- Replaces: 26081120, 26067714, 26085928
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Buick Century | Custom, Limited | 6 Cyl 3.1 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1997071
$59.75 MSRP: $106.69
You Save: $46.94 (44%)
ADD TO CART
Product Specifications
- Other Name: Switch-Turn Signal; Windshield Washer Switch; Multi Purpose Switch; Turn Signal & Hazard Switch; Front Wiper Switch; Lever
- Replaced by: 01995974
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1990 Buick Century | Custom, Estate Wagon, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1999446
$50.81 MSRP: $60.05
You Save: $9.24 (16%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Assembly-Turn Signal & Headlamp Dimmer & Cruise Control; Multi Purpose Switch; Multifunction Switch; Headlamp, Wiper & Washer Control; Turn Signal Lamp; Headlamp Dimmer.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Century Headlamp Switch, Black Part Number: 25140856
Product Specifications
- Other Name: Lever, Turn Signal Control; Multi Purpose Switch; Signal Lever; Engagement Switch; Turn/Wiper Lever; Lever
- Replaces: 25111219, 25111596, 25111638, 25111597, 25111639, 25111761, 25111217, 25111224, 25111598
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 25111290
Product Specifications
- Other Name: Lever, Multi Purpose Switch for Turn Signal, Headlamp Dimmer, Cruise Control, Wiper & Washer.; Signal Lever; Turn/Wiper Lever; Lever; Lever, Turn Signal Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Buick Century | Custom, Estate Wagon, Limited, Special, T-Type | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Combination Switch Part Number: 22510144
Product Specifications
- Other Name: Lever, Turn Signal & Headlamp Dimmer Switch & Windshield Wiper & Windshield Washer; Signal Lever; Lever; Lever, Turn Signal Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
View related parts
Buick Century Combination Switch Part Number: 22510143
Product Specifications
- Other Name: Lever, Turn Signal Control; Signal Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Buick Century | Custom, Estate Wagon, Limited, Special, T-Type | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Turn Signal Switch Part Number: 1997988
Product Specifications
- Other Name: Switch, Turn Signal; Hazard Flasher Switch; Multi Purpose Switch; Hazard Switch; Signal Switch; Turn Signal & Hazard Switch; Switch; Lever; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Buick Century | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Signal Switch Part Number: 1997073
Product Specifications
- Other Name: Switch-Turn Signal; Switch, Turn Signal Lamp
- Replaces: 1997087
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | Custom, Limited, Special | 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Multifunction Switch Part Number: 25111261
Product Specifications
- Other Name: Lever, Transmission Control Lever; Multi Purpose Switch; Engagement Switch; Lever
- Replaced by: 19353956
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick Century | Custom, Estate, Estate Wagon, Limited, Olympia Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Turn Signal Switch Part Number: 1997090
Product Specifications
- Other Name: Turn Signa; Multi Purpose Switch; Signal Switch; Turn Signal & Hazard Switch; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | Custom, Limited, Special | 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1997087
Product Specifications
- Other Name: Switch-T; Multi Purpose Switch; Turn Signal & Hazard Switch
- Replaced by: 1997073
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Century | Custom, Limited, Special | 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1997072
Product Specifications
- Other Name: Turn Signa; Multi Purpose Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1990 Buick Century | Custom, Estate Wagon, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1997055
Product Specifications
- Other Name: Turn Signa; Multi Purpose Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1988 Buick Century | Custom, Estate Wagon, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Century Combination Switch Part Number: 25110866
Product Specifications
- Other Name: Lever Assembly-Turn Signal & Cruise Control Actuator; Signal Lever; Engagement Switch; Turn/Wiper Lever; Lever; Lever, Turn Signal Control
- Replaces: 25111264
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | Custom, Limited, Special | 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1995980
Product Specifications
- Other Name: Switch, Turn Signal; Multi Purpose Switch; Signal Switch; Switch, Turn Signal Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Turn Signal Switch Part Number: 1995974
Product Specifications
- Other Name: Switch Assembly, Turn Signal; Multi Purpose Switch; Signal Switch; Switch, Turn Signal Lamp; Switch, Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1990 Buick Century | Custom, Estate Wagon, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.3 L GAS

Buick Century Turn Signal Switch

Want to cut long-term maintenance and repair costs? Choose OEM Turn Signal Switch. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Century parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Century Turn Signal Switch includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Buick Century Turn Signal Switch Parts and Q&A

Turn Signal Switch
88963625
Q: How to replace the Hazard Warning Switch and Turn Signal Switch on Buick Century?
A:
Begin switch replacement only when you see the lever centered at off position and cut off the battery's negative side. Turn off the sir before taking out the Steering Wheel and steering column decorative panels. Disconnect wire harness straps from the column assembly and remove the multifunction, turn signal, and hazard switch assembly connector from its connection to the sir coil assembly. Take out the multifunction switch assembly from the steering column by unplugging the bulkhead connectors and serving the switch assembly supports. Separate the steering column tilt head assembly from its multifunction and hazard switch unit. Use a small flat-port tool to push down the electrical contact and set the control switch on top of the steering column. Ensure that the electrical contact rests lightly on the turn signal cancellation cam. Turn the screws to 7 nm (62 inch lbs.) as you join the switch assembly connectors to both the steering column bulkhead and sir coil assembly connectors. Connect the wire harness assembly back to its position on the steering column supports, make sure the lever remains off, and put on the steering column trim panels and Steering Wheel. Reenable the sir system after reconnecting the battery's negative terminal.
Turn Signal Switch
88964579
Q: How to remove and install the Turn Signal Switch on Buick Century?
A:
Begin the multifunction turn signal lever removal procedure by placing the lever at the off position center and disconnecting the negative Battery Cable and disabling the sir system. The first step requires removal of the inflatable restraint Steering Wheel module followed by unstalling of the Steering Wheel while performing the same procedure for the steering column trim covers. Use heat shrinks to detach the steering column wire harness from its retainer then unfasten the two wire harness straps from the wire harness. Disconnect the steering column bulkhead connector from both the vehicle wire harness and the gray and black connectors from the multifunction turn signal lever steering column bulkhead connector. Start by removing bolts from the multifunction turn signal lever and move the lever out of the steering column. Installation of the multifunction turn signal lever requires using a small flat-blade to compress electrical contacts placing them on the canceling cam prior to positioning the lever in its original spot. Secure the multifunction turn signal lever with bolts and tighten each one to 6 nm (53 inch lbs.). Set the gray and black connectors into position with the multifunction turn signal lever steering column bulkhead connector before finalizing the connection between this bulkhead connector and the vehicle wire harness. Return the steering column wire harness into its retaining piece then fasten the straps from the wire harness onto it. After installing the steering column trim cover check that the lever points to center position or off and reinstall the Steering Wheel with the inflatable restraint Steering Wheel module. Reconnect the negative Battery Cable after enabling the sir system.