How to replace the rear brake line (Caliper) on 2008 Chevrolet Cobalt?

In order to switch the rear brake hose you should first lift and stabilize your vehicle then take off the wheel and tire. Repel any foreign matter and dirt particles from both brake pipe and hose ends. Before removal of the brake hose from its brake pipe connections you should seal both ends with caps or plugs to prevent any fluid leak or contamination. Separate the brake hose mounting bracket by pulling its retaining clip out. Remove the hose from its place. Take out the brake hose fitting bolt from the brake caliper and throw away the copper brake hose gaskets. To protect the system seal the openings of the caliper and hose using cap or plug solutions. Install new copper brake hose gaskets before putting the hose fittings together. Install the brake hose assembly to the brake caliper then tighten the bolt to 48 N.m (35 lb ft) as you place the brake hose gaskets and fitting bolt on the brake hose. Use the brake hose to attach it to the mounting bracket with the hose fitting resting in the notch and fasten it with the retaining clip. To attach the brake pipe fitting at the rear brake hose use a back up wrench and tighten it to 21 N.m (15 lb ft). Replace the tire assembly while making sure the hose stays away from suspension parts. Also fix the hose contact issue when you find it. Before bringing the vehicle down lower the hydraulic system through bleeding steps.

OEM 2008 Chevrolet Cobalt Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Lines found

View related parts
2008 Chevrolet Cobalt Flex Hose Part Number: 19366736
$12.99 MSRP: $31.20
You Save: $18.21 (59%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake Front; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front and Rear
- Replaces: 22706789
- Item Weight: 0.50 Pounds
- Item Dimensions: 6.4 x 3.4 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19366736
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet Cobalt Flex Hose, Rear Driver Side Part Number: 19366742
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 19331548, 22720042
- Item Weight: 0.60 Pounds
- Item Dimensions: 7.2 x 3.2 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366742
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet Cobalt Flex Hose, Front Part Number: 19366692
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Replaces: 22716552, 15870413
- Item Weight: 1.30 Pounds
- Item Dimensions: 5.2 x 2.0 x 12.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366692
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet Cobalt Flex Hose, Rear Passenger Side Part Number: 19366741
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Replaces: 22720049, 19331547
- Item Weight: 0.60 Pounds
- Item Dimensions: 6.8 x 3.2 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366741
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet Cobalt Flex Hose, Front Part Number: 15939642
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Item Weight: 0.80 Pounds
- Item Dimensions: 17.7 x 1.9 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15939642
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS
View related parts
2008 Chevrolet Cobalt Brake Hose Part Number: 25820531
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Line
- Position: Rear
- Item Weight: 0.50 Pounds
- Item Dimensions: 11.3 x 3.4 x 0.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 25820531
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS

2008 Chevrolet Cobalt Brake Line

With a comprehensive array of OEM 2008 Chevrolet Cobalt Brake Line, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Chevrolet Cobalt Brake Line are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Chevrolet Cobalt Brake Line Parts and Q&A

Q: How to replace the rear brake line (Caliper) on 2008 Chevrolet Cobalt?
A: In order to switch the rear brake hose you should first lift and stabilize your vehicle then take off the wheel and tire. Repel any foreign matter and dirt particles from both brake pipe and hose ends. Before removal of the brake hose from its brake pipe connections you should seal both ends with caps or plugs to prevent any fluid leak or contamination. Separate the brake hose mounting bracket by pulling its retaining clip out. Remove the hose from its place. Take out the brake hose fitting bolt from the brake caliper and throw away the copper brake hose gaskets. To protect the system seal the openings of the caliper and hose using cap or plug solutions. Install new copper brake hose gaskets before putting the hose fittings together. Install the brake hose assembly to the brake caliper then tighten the bolt to 48 N.m (35 lb ft) as you place the brake hose gaskets and fitting bolt on the brake hose. Use the brake hose to attach it to the mounting bracket with the hose fitting resting in the notch and fasten it with the retaining clip. To attach the brake pipe fitting at the rear brake hose use a back up wrench and tighten it to 21 N.m (15 lb ft). Replace the tire assembly while making sure the hose stays away from suspension parts. Also fix the hose contact issue when you find it. Before bringing the vehicle down lower the hydraulic system through bleeding steps.