How to perform a front Brake Calipers overhaul on 2003 Buick Rendezvous?

To work on front Brake Calipers you need a dust boot seal installer (part J 36349). First examine how much brake fluid is in the master cylinder reservoir and drain extra to reach the middle level between acceptable marks. Keep your fingers behind the piston when you apply compressed air because they could unleash at high speed during piston removal from the caliper. Compressed air helps push the Brake Caliper Piston through the piston boot without cleaning materials. When you spot damage on the piston during examination you need to replace it immediately. Look for damage on the caliper bore and seal grooves using a small plastic or wooden tool to remove the piston seal. You should polish away minor caliper corrosion using crocus cloth but need a new brake caliper to fix severe rust damage. Check brake caliper bolt boots and bolts for damages then replace them but steer clear from polishing off corrosion. Spray denatured alcohol on all caliper parts then dry them through air filter and non-lubricated compressed air. Mount the bleeder valve then cap and put on new lubricated piston seal and boot at the caliper brake piston. Slip engine oil on the piston then place it in the caliper hole while using the boot tool to line up the dust shield (J 36349). Next add the caliper in place.

OEM 2003 Buick Rendezvous Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Brake Calipers found

View related parts
2003 Buick Rendezvous Caliper Overhaul Kit, Rear Part Number: 18023387
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 9.2 x 7.9 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18023387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2003 Buick Rendezvous Caliper, Passenger Side Part Number: 10434251
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 10.40 Pounds
- Item Dimensions: 7.1 x 4.0 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10434251
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2003 Buick Rendezvous Caliper, Driver Side Part Number: 10434252
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 11.10 Pounds
- Item Dimensions: 10.4 x 9.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10434252
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2003 Buick Rendezvous Caliper, Passenger Side Part Number: 18044881
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Item Weight: 5.50 Pounds
- Item Dimensions: 9.9 x 7.4 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18044881
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
2003 Buick Rendezvous Caliper, Driver Side Part Number: 18044880
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Item Weight: 4.50 Pounds
- Item Dimensions: 9.6 x 7.6 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18044880
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Buick Rendezvous Submodels:
- CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS

2003 Buick Rendezvous Brake Calipers

With a comprehensive array of OEM 2003 Buick Rendezvous Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2003 Buick Rendezvous Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2003 Buick Rendezvous Brake Calipers Parts and Q&A

Q: How to perform a front Brake Calipers overhaul on 2003 Buick Rendezvous?
A: To work on front Brake Calipers you need a dust boot seal installer (part J 36349). First examine how much brake fluid is in the master cylinder reservoir and drain extra to reach the middle level between acceptable marks. Keep your fingers behind the piston when you apply compressed air because they could unleash at high speed during piston removal from the caliper. Compressed air helps push the Brake Caliper Piston through the piston boot without cleaning materials. When you spot damage on the piston during examination you need to replace it immediately. Look for damage on the caliper bore and seal grooves using a small plastic or wooden tool to remove the piston seal. You should polish away minor caliper corrosion using crocus cloth but need a new brake caliper to fix severe rust damage. Check brake caliper bolt boots and bolts for damages then replace them but steer clear from polishing off corrosion. Spray denatured alcohol on all caliper parts then dry them through air filter and non-lubricated compressed air. Mount the bleeder valve then cap and put on new lubricated piston seal and boot at the caliper brake piston. Slip engine oil on the piston then place it in the caliper hole while using the boot tool to line up the dust shield (J 36349). Next add the caliper in place.