How to Replace a Power Steering Hose for Pressure Hose on 2002 Chevrolet Venture?

The initial steps for replacing the power steering pressure hose consist of properly raising and supporting the vehicle. Your first step should be disconnecting the intermediate shaft connecting to the steering gear to prevent damage which might cause steering control problems. The intermediate shaft should be disconnected from the steering gear after which you need to secure the frame rear using a utility stand while you detach frame rear bolts from the assembly. You must lower the frame rear section to access the area while setting a drain pan in position under the Power Steering Pump and gear. After taking the inlet hose off the steering gear along with the hose clip you should elevate the frame rear and fit the old bolts loosely. Lower the vehicle while discarding the Drive Belt followed by removing the inlet hose from the pump and hose retainer. The installation procedure should begin with inlet hose installation followed by its connection to the pump which requires 27 nm (20 ft. Lbs.) tightening torque. Install the power steering inlet hose after attaching it to the hose retainer device then place the Drive Belt into position. A utility stand should be used to hold the frame rear before finally raising the vehicle. After discarding the frame rear bolts users should lower the frame rear section to gain access before securely tightening the inlet hose to the steering gear at 27 nm (20 ft. Lbs.). Then you must reinstall the power steering gear hose clip along with the frame rear elevation and the installation of new frame rear bolts. Attach the intermediate shaft to the steering gear after you lower the vehicle while adding power steering fluid to the reservoir and bleaching the steering system.

OEM 2002 Chevrolet Venture Power Steering Hose

Power Steering Pressure Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Power Steering Hoses found

View related parts
2002 Chevrolet Venture Power Steering Cooler Part Number: 26076946
Product Specifications
- Other Name: Hose, Steering Fluid Cooler
- Replaces: 10309270, 26079270
- Item Weight: 1.80 Pounds
- Item Dimensions: 38.0 x 29.3 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26076946
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Power Steering Return Hose Part Number: 26075225
Product Specifications
- Other Name: Hose, Steering Gear Oil Return; Power Steering Hose; Return Hose; Return Tube; Upper Return Hose; Pipe, Steering Gear Oil Return
- Item Weight: 0.60 Pounds
- Item Dimensions: 6.8 x 21.8 x 1.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26075225
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Power Steering Cooler Part Number: 15777624
Product Specifications
- Other Name: Hose Assembly-Power Steering Fluid Cooling; Cooling Pipe; Power Steering Oil Cooler; Hose, Steering Fluid Cooler
- Replaces: 26073959
- Item Weight: 1.60 Pounds
- Item Dimensions: 31.2 x 26.0 x 9.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777624
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Power Steering Pressure Hose Part Number: 15777622
Product Specifications
- Other Name: Hose Assembly-Power Steering Gear Inlet; Power Steering Hose; Pressure Hose; Hose, Hydraulic Steering Gear Pressure; Hose, Steering Gear Oil Pressure
- Replaces: 10311306
- Item Weight: 1.80 Pounds
- Item Dimensions: 22.9 x 20.5 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777622
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Pipe Kit, Driver Side Part Number: 26081830
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Driver Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 10.7 x 3.7 x 1.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26081830
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Pipe Kit, Passenger Side Part Number: 26081831
Product Specifications
- Other Name: Pipe Kit, Steering Gear; Power Steering Hose; Pressure Line; Line Kit; Line; Pipe Kit, Hydraulic Steering Gear Pressure; Pipe Kit, Steering Gear Oil Pressure
- Position: Passenger Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 18.2 x 3.1 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26081831
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Power Steering Return Hose Part Number: 15777620
Product Specifications
- Other Name: Pipe, Steering Gear Oil Return; Power Steering Hose; Return Hose
- Replaces: 26073960
- Item Weight: 0.70 Pounds
- Item Dimensions: 23.0 x 6.1 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15777620
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Pipe Kit, Passenger Side Part Number: 26045506
Product Specifications
- Other Name: Pipe Kit, Steering Gear Oil Pressure; Power Steering Hose; Pressure Line; Line Kit; Line
- Position: Passenger Side
- Item Weight: 1.10 Pounds
- Item Dimensions: 20.3 x 6.2 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26045506
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
2002 Chevrolet Venture Pipe Kit, Driver Side Part Number: 26045505
Product Specifications
- Other Name: Pipe Kit, Steering Gear Oil Pressure; Power Steering Hose; Pressure Line; Line Kit; Line
- Position: Driver Side
- Item Weight: 0.70 Pounds
- Item Dimensions: 12.5 x 4.2 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 26045505
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Venture Submodels:
- Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS

2002 Chevrolet Venture Power Steering Hose

With a comprehensive array of OEM 2002 Chevrolet Venture Power Steering Hose, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2002 Chevrolet Venture Power Steering Hose are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2002 Chevrolet Venture Power Steering Hose Parts and Q&A

Q: How to Replace a Power Steering Hose for Pressure Hose on 2002 Chevrolet Venture?
A: The initial steps for replacing the power steering pressure hose consist of properly raising and supporting the vehicle. Your first step should be disconnecting the intermediate shaft connecting to the steering gear to prevent damage which might cause steering control problems. The intermediate shaft should be disconnected from the steering gear after which you need to secure the frame rear using a utility stand while you detach frame rear bolts from the assembly. You must lower the frame rear section to access the area while setting a drain pan in position under the Power Steering Pump and gear. After taking the inlet hose off the steering gear along with the hose clip you should elevate the frame rear and fit the old bolts loosely. Lower the vehicle while discarding the Drive Belt followed by removing the inlet hose from the pump and hose retainer. The installation procedure should begin with inlet hose installation followed by its connection to the pump which requires 27 nm (20 ft. Lbs.) tightening torque. Install the power steering inlet hose after attaching it to the hose retainer device then place the Drive Belt into position. A utility stand should be used to hold the frame rear before finally raising the vehicle. After discarding the frame rear bolts users should lower the frame rear section to gain access before securely tightening the inlet hose to the steering gear at 27 nm (20 ft. Lbs.). Then you must reinstall the power steering gear hose clip along with the frame rear elevation and the installation of new frame rear bolts. Attach the intermediate shaft to the steering gear after you lower the vehicle while adding power steering fluid to the reservoir and bleaching the steering system.