ChevyParts
My Garage
My Account
Cart
OEM 2001 Chevrolet Impala ABS Control Module
Anti Lock Brake Control Module- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 ABS Control Modules found
2001 Chevrolet Impala Control Module Part Number: 12221450
Product Specifications- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module
- Replaced by: 18078136
- Item Weight: 1.30 Pounds
- Item Dimensions: 6.2 x 6.2 x 5.3 inches
- Condition: New
- SKU: 12221450
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2001 Chevrolet Impala Control Module Part Number: 12221451
Product Specifications- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module
- Replaced by: 18078143
- Item Weight: 1.30 Pounds
- Item Dimensions: 6.1 x 6.2 x 5.1 inches
- Condition: New
- SKU: 12221451
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2001 Chevrolet Impala Control Module Part Number: 12221452
Product Specifications- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module
- Replaced by: 18078147
- Item Weight: 1.30 Pounds
- Item Dimensions: 7.1 x 6.1 x 4.1 inches
- Condition: New
- SKU: 12221452
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2001 Chevrolet Impala ABS Control Module
With a comprehensive array of OEM 2001 Chevrolet Impala ABS Control Module, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2001 Chevrolet Impala ABS Control Module are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.
2001 Chevrolet Impala ABS Control Module Parts and Q&A
- Q: How to replace the ABS Control Module on 2001 Chevrolet Impala?A: The process of ABS Control Module replacement starts by verifying the Ignition Switch is set to off to avoid harming equipment. Start by removing the red locking tab from the connector lock tab then press down on the lock tab to expose the sliding connector cover for disconnecting the ABS Control Module harness connector. The assembly removal procedure requires cleaning all dirt but avoids using tools to pry parts or damaging bpmv surfaces or solenoid valves. Hover the ABS Control Module away from the bpmv by gently pulling on its end after screw removal of the 4 screws which connect them. To install the ABS Control Module you should first use a clean rag to clean the bpmv surface with alcohol and then place the ABS Control Module on the bpmv and fasten it with the 4 screws until they reach 5 nm (44 inch lbs.). Reconnect the ABS Control Module harness connector after pushing the lock tab and install the sliding connector cover back to the locked position then return the red locking tab. Complete the diagnostic system check - abs after setting the Ignition Switch to run with no engine start followed by the installation steps.
Related 2001 Chevrolet Impala Parts
2001 Chevrolet Impala Wheel Bearing
2001 Chevrolet Impala ABS Wheel Speed Sensor Connector
2001 Chevrolet Impala Brake Backing Plate
2001 Chevrolet Impala Brake Caliper Bracket
2001 Chevrolet Impala Brake Caliper Repair Kit
2001 Chevrolet Impala Brake Calipers
2001 Chevrolet Impala Brake Pad
2001 Chevrolet Impala Brake Proportioning Valve
2001 Chevrolet Impala Hydraulic Hose
2001 Chevrolet Impala Parking Brake Cable
2001 Chevrolet Impala Parking Brake Shoe
2001 Chevrolet Impala Wheel Hub Bolt